hi all
so, currently i have a rear feed shower arm and a rainfall head. is there any connector or elbow we could replace the arm with, that would enable us to connect a handest shower head instead?
On bad advice our builder installed a no brand/cheap built in shower mixer in our new bathroom 5 years ago.
It has stopped working - and the water is almost impossible to adjust to the right temperature - and changes temp when other taps in the house are turned on/off.
We have been told that...
First time novice, I thought I had a problem with my shower pump as the flow was much lower than normal. Pure coincidence but this happened just after I had my H/W cylinder replaced.
My shower is gravity feed from the H/W cylinder and a separate C/W tank, both located in the loft. I only have...
Hi, I am fitting at Stuart turner shower mate eco 1.5 bar.
My question is, can the inlet be from a 15mm source? The provided flexible hose that comes with it is 15mm.
I just cant get get to the 22mm pipe easily.
What are your thoughts?
Cheers
this may sound a basic question, but it is important. I have seen so many conflicting opinions, even from manufacturers. Some say, just use the biggest bore possible, others say use a small bore 8mm for a fully pumped system & a large bore 11mm for a gravity system. There must be a reason why...
We have a shower on a gravity fed system that isn't quite powerful enough to provide an acceptable flow. Don't need a power shower, just a relatively modest increase in pressure. As an alternative to a full size shower pump, has anyone had experience of installing/using the Floflex SP2B In-Line...
Hi. For the first time since moving in 7 years ago, my pre-existing bath hot tap is only running luke warm to cold. The attached shower is the usual decent hot temp as is the basin and kitchen tap. (I've got a combi boiler.) From reading the forums I thought maybe the thermostat cartridge might...
Hi, I'm about to buy a thermostatic shower and decided on the Hansgrohe Crometta 240. On Amazon this has hundreds of good reviews and believe the brand has a good reputation and build quality, so would be a good choice.
However, I've just viewed a YouTube video by a plumber installing and...
I ordered a McAlpine 90mm x 50mm shower trap for my walk-in shower. The base will be 18mm ply with the shower tray bedded in mortar on top. I don't think the threads of the top half of the trap are going to reach the threads of the bottom half when I assemble everything. I really need more...
I am ready to waterproof my walk-in shower ready for tiling. The walls are Aquapanel sheets fitted to stud walls, joined with Aquapanel adhesive, and the base is 18mm marine ply screwed to joists. I'm looking at the Mapei shower waterproofing kit from Screwfix.
Got a few questions...
Should I...
Hello,
I’m trying to fit a diverter to a Grohe concetto single hole mixer tap. I have removed the aerator but cannot find any adapter that will fit as the opening is at an angle. The removed aerator is F22 female and screws onto plastic threads that look like a hexagon when looking up into the...
Hello.
Installing a shiny new Hudson Reed shower in France...
The shower comes with two stem adapters.
No matter how hard I tighten these they leak significantly....
BUT if I then remove shower and screw in the previous end caps...no leaks..in fact I only need to hand tighten these..
Pictures...
For some reason I'm not getting hot water coming out of the bath tap it's just coming out warm, it's fitted with these anti scald valves underneath the bath, I have taken the side pannel of the bath thinking it would be easy to adjust to see if that's the problem, looking at it I have no idea...
I have a traditional British bathroom sink with 2 separate taps for cold and hot water. I need a bridge mixer tap for it. The problem is I only seem to find ones with 180mm tap connection centres, while mine needs 200mm. IS there hope?
Hi everyone,
I hope someone can help thanks.
I have had a new wet room installed and overall it has been done excellent. However, I have one problem and need advice.
As part of the fit it was to get a 450mm wide wall hung basin. It was hung on the wall on top of the new wet wall and gyproc so...
Hi all. It’s been a while since fitting a bath for a customer but I’m looking for some solid recommendations if possible. I know they all look similar but don’t want anything squeaking when it’s stood in. Cheers.
I have what appears to be a little used bath taps/mixer with shower outlet, without connecting it all up, I notice the collar that obviously diverts the flow to a shower head, does not stay in place when pushed down. Would this be different when connected and with water pressure, or is it...
Hi there I hope you can help
The clip on the top of my bi fold shower door has snapped so it won’t stay closed
Can anyone help at all as to where I might be able to source one?
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.