Hello
I am trying to find out what has caused these small circular shapes on my guest toilet's ceiling. Is it water damage or from some cleaning or steaming that was done on the wall tiles?
Thank you.
Hello, have a 4m run of 50mm pipe for the shower. The layout of joists, closeness of corner walls etc mean that it would be very helpful to be able to add the basin waste to a swept tee in the shower waste and this could be between 300-800mm from the soil stack . I've read elsewhere very mixed...
So a Salamander pump has been fitted. The cold feed is standard coming from tank, the hot I was supplied with an s Flange. I never use these, only Essex flanges.
The cold water works well and has good pressure, but there is no hot. There is hot at the tap though.
Any ideas guys?
Thanks
Hello. I'm connecting a long run of 50mm solvent weld waste pipe from a shower to the stack (compliant with regs hence 50mm). The soil stack branch is Hunter and I bought a Hunter solvent weld boss adapter to fit on it. However, the waste pipe (Floplast I think)is a loose fit in the adapter...
A couple of issues I’m hoping can be solved here!
The shower in our en suite is far too hot, and the temperature control just feels loose i.e when you turn it there’s no resistance and the temperature doesn’t change. It also only turns about 45 degrees which also doesnt seem right.
I’ve...
Hi All,
not sure if anyone seen these wastes before?
We have them in all 3 showers in our house we just moved into and they water seems to drain slowly from them.
Just never seen these shower traps before.
Any ideas of how I can unblock or should I put some liquid drain unblocker down.
Nearly got it all out...I am going to put a double vanity unit here...the previous unit was on the opposite wall so two hot and two cold feeds off the manifold are not required..how to tidy all this up ?
I could remove the manifold but was thinking of just boxing it in ?
As to the hole...in fill...
We had a plumber install a high rise low flow (1.6 gal / flush) toilet about a year ago. It worked fine for about 6 months. Since then, the plumber has been here 3 times because the toilet won't flush properly. The plumber has used a RIGID tool. He has replaced the ball cock and cleaned the...
Good afternoon guys,
I was wondreing if anyone could help with the issue I have at home.
I have a MIRA offset quadrant shower (built around 3/4 years ago approx), and I am having leakings (see attached the photos). I have tried to put some silicone several times but the water is still going...
Hello, been doing bathrooms a while now, and always tank whatever wet area I’m working on according to manufacturers instructions. I always have tanking liquid left over, never any tape (which is expensive to buy separately). Does anyone have any experience of using a cheaper waterproof tape as...
Hi, I'm installing a shower in an upstairs bathroom. The household boiler is a Potterton Performa HE condensing combi-boiler. During testing of the shower, I was unable to get a flow of hot water. Hot water is available however from the kitchen tap downstairs although it takes ages to come...
Hi there, we are due to have a new shower room built in a loft conversion. We are a family of 5, with one existing bathroom. Will we need to have an unvented hot water system installed to enable the 2 showers to run successfully at the same time?
Pressure and flow at house is 2 bars/18 litres...
Hi. We have an aqualisa shower that has developed an intermittent problem. Been working fine then one day I pressed start and water came out for a split second, stopped, and the device became unresponsive to any key presses with the "boost" and blue/red lights stuck on (usually in working order...
I have a macerator which does a toilet, sink and shower in our basement, it has worked fine for 2 years then water started backing up into shower tray so I took the macerator out (3 hr job due to location) and the non-return valve had come a bit loose. Repaired that, gave it a good clean out...
Hi, any help appreciated with this, ideally would like to avoid having to rip out and replace full bath, would just like to find replacement panel, but struggling with this
Measurements seem weird
Length of panel = 1690 mm
Height of panel = 535 mm
Length to start of curve = 620 mm
Size of the...
Trying to remove a bath...thought I had done the hard part with the chisel and the surround...but it simply will not budge...its plastic/fibreglass...can I just cut along the edge with a jigsaw ?? Any issues with dust from the cutting ?
Thanks.
Hi I have a thermostatic rainfall shower and it also also has a hand held shower with hose attached to it. I was checking the temperatures by adjusting the thermostatic bar valve and when the bar valve is set at 40c the rainfall shower is around 37 degrees but the hand held shower is 40c, so...
Looking for some help with the shower pressure issue.
Issue had started after my boiler was replaced to a combi-boiler (worcester bosch greenstar 30i) about a year ago now. Hot water the shower is supplied from the combi boiler downstairs with cold water coming from the cold water tank in the...
Morning
I have fitted this twice now as part of a bathroom refurb - small rooms 2m sq approx. I've not had any issues. However MI's say not to put heavy items on this type of flooring but instead cut around with appropriate expansion gap. Well that to my mind eliminates a bathroom !! for this...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.