Discuss T4TS plumbing scenarios in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

LUCIALIA

Plumbers Arms member
Plumber
Messages
220
Is anyone else having any problems with the scenarios, i just wanna chuck it out of the bloody window. If anyone has any walk throughs, it would be appreciated as i can fix the problem no worries but not complete it exactly as the program wants & it driving me nuts!
 
hi mate i dont know how to do soundness test in senario 3
please help me
akh
 
hi mate, the scenarios are a pain,,,scenario 1 their are nineteen thing to check basically everything to do with the cold water system, count them as you go along isolators,taps,toilet etc,etc....
scenario 2 hot water check,the immersion heater has been left on and its too high,turn it down to 60 degrees again check everything to do with the hot water,
scenariol 3 not done that yet,got as far as a soundness test and failed so got bored with it.....good luck
 
hi got this disk of a mate for fun.
check every thing that is wet plumbing, it will tell you if not relevant.
and dont forget to leave the house as you found it water / heat on doors shut etc.
 
Good day one and all, I am also struggling with the soundness testing!! do you have to check each piece of pipework which is adjoined to the isolation/service valves?! I do know after many times of being told that you must turn the boiler OFF before you play with the gate valve. Will give it another attempt when kids are tucked up in bed!
Regards James
 
I am also struggling with the soundness test in sanario 3, if anyone has any advice it will be very much appreciated
 
are you referring to a gas tightness test ?
 
Last edited by a moderator:
no the soundness test for hot and cold water systems. (scenario 3 on the Trade 4 trade skills virtual reality cd). Ive read the guide in my book but its not the same in the VR house, you cant just go to your toolbox and grab a tool. the last problem i had to solve was two leaking taps but it wouldnt let me change the tap washers i had to replace the taps with new ones, shurely i should have had both options.
 
Last edited by a moderator:
Did anybody finish the senario 2. I have problem with the hot water system check, rest is done, it is 18 points to inspect. Somebody can tell my whom from kitchen&cupboard has to by inspect. help please its getting me mad
 
I have not heard of these scenarios are they part of an on line plumbing course ? Where do you get the Cd's ?
 
Status
Not open for further replies.

Reply to T4TS plumbing scenarios in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Good morning, I recently had an extension, new bathroom and new en-suite fitted. Prior to the works the hot water worked. Now we have moved...
Replies
13
Views
3K
R
  • Locked
Hi, My rather old immersion boiler decided to give up the ghost the other day, notifying the household by tripping the switches at the fuse box...
Replies
12
Views
2K
rflook
R
D
  • Locked
First time posting on here and I am after some help and advice on a project I have ongoing at home - a bit cheeky I know but as they say around...
Replies
3
Views
2K
S
  • Locked
Are you sitting comfortably? Good, now here's a story. Called to a larger property with a big unvented cylinder (Megaflo). About a year ago it...
Replies
10
Views
3K
mountainman
M
M
  • Locked
Hi all. We have had a few issues with our boiler over a couple of years, which I'll try to keep concise. We have a condensing boiler in the...
Replies
26
Views
5K
mountainman
M
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock