Discuss Interesting use of plumbing skills in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
G

Garryaca@yahoo.

Useing a few tricks of the trade on my cargo bike!

[DLMURL="http://www.flickr.com/photos/13725084@N05/4338378222"]DSC09219 on Flickr - Photo Sharing![/DLMURL]

[DLMURL="http://www.flickr.com/photos/13725084@N05/4338377694"]DSC09217 on Flickr - Photo Sharing![/DLMURL]

[DLMURL="http://www.flickr.com/photos/13725084@N05/4338377168"]DSC09216 on Flickr - Photo Sharing![/DLMURL]

[DLMURL="http://www.flickr.com/photos/13725084@N05/4338376702"]DSC09215 on Flickr - Photo Sharing![/DLMURL]

[DLMURL="http://www.flickr.com/photos/13725084@N05/4338378222"]DSC09219 on Flickr - Photo Sharing![/DLMURL]
 
Last edited by a moderator:
i bet the fittings are worth more than the bike.R.O.F.L:D:D:D.
i did see a programme recently where a plumber was using his motorbike for work,tooled up and all that,the police who pulled him over were not too impressed though:)
si
 
Ingenious!

I recently bent a piece of 22mm for a shower rail. Customer was really chuffed - and I was too - 3 bends and only 1mm out and ended up totally flat when laid on the floor - fluke!
 
if it were i, i would consider remaking the whole bike with 28mm and guttering for the mud guard.
good rolling add.
i started of as a pipe welder at ralliegh bikes, not much difference.
 
I did get a funny look from the guy at the plumb centre when I turned up on a push bike and bought 3 metres of tube!..

(sliced it in half and strapped it to the top tube)
 
I did get a funny look from the guy at the plumb centre when I turned up on a push bike and bought 3 metres of tube!..

(sliced it in half and strapped it to the top tube)
i remember when all the gas board fitters had push bikes to go out doing the small jobs these were the days before flexi,s on cookers and they were hard piped wasnt unusual for a cooker to have several nipples and socket joining it as they didnt like having to thread anything
they actuallly had a pipe vice fitted on the bike and a small set of stocks and dies in the panniers and a couple of 4 foots of barrel strapped on the cross bar
 
Status
Not open for further replies.

Reply to Interesting use of plumbing skills in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two...
Replies
2
Views
223
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new...
Replies
1
Views
275
We run a community village hall and have a large kitchen provided for the use of hirers. This includes a Lincat SLR9 gas cooker which I believe is...
Replies
5
Views
560
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4...
Replies
9
Views
462
Hi all Noticed bad smell in my drain out side put my hand down and it unclogged it for now however I checked my sewer drain and after flushing my...
Replies
3
Views
571
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock