Search the forum,

Discuss Thermostat setting in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Messages
2
Hi

How can I set me water tank thermostat correctly so it is using the cheapest tariff of electric . I have attached a picture ... thanks
BC1549DC-73AE-4038-A275-29F41BA996CA.jpeg
 
Hi

How can I set me water tank thermostat correctly so it is using the cheapest tariff of electric . I have attached a picture . thanks View attachment 40153
See page 26 of the instructions:

The little white sliders (tappets) round the outside of the clock dial need to be pushed inwards around the dial (off)for the daytime hours, leaving them in the outward position (on) only during your cheap rate period (whatever that is, say 12.00pm till 6.00am)

At the moment it seems to be on all the time.
 
See page 26 of the instructions:

The little white sliders (tappets) round the outside of the clock dial need to be pushed inwards around the dial (off)for the daytime hours, leaving them in the outward position (on) only during your cheap rate period (whatever that is, say 12.00pm till 6.00am)

At the moment it seems to be on all the time.
Thank you very much !! Problem solved
 
Yes agreed , most think its cheaper at night , especially when a programmer says “ off peak “ .
Couple of years back I had a quote from Scottish Power, and their prices were 12.363p day, 5.31p night. They based the quote on 55% of usage at night, when even if hourly use was same round the clock (unlikely) it would be less than 30%. Clearly a try-on to reel me in by getting the apparent cost down. I didn't buy.
 
I have just fitted this on a economy 7 system, set to 12.00am - 7.00am I would employ a engineer to check you have economy 7 and the immersion heater is connected to the off peak board , as this one was wired wrong. Kop
 

Attachments

  • IMG_20190828_153830.jpg
    IMG_20190828_153830.jpg
    1.2 MB · Views: 9

Reply to Thermostat setting in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I have an ideal vogue max S18 boiler and I’m considering fitting auto balancing TRVs, my question relates to the boilers pump. I see a boiler pump menu for either 70% or 100%, so, is the pump set at either one of two fixed speed percentages or does the pump actually vary speed, (modulate)...
Replies
1
Views
139
Hi guys. I'm trying to identify a toilet model before ordering a seat for a customer. I went to what used to be a Roca stockist (they no longer are) and one of the guys there reckoned it might be "The Gap". I went to the new stockist and the guy there disagreed it was "The Gap" and that he'd...
Replies
2
Views
132
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
95
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
6
Views
282
Our kitchen mixer tap has started dripping. Like so much of the plumbing in our almost new build bungalow, it is lacking! The plumber didn't install any isolating cocks in the H&C feed to the tap so how can I identify which of the valves is passing? Shut the whole H&C water system down?
Replies
12
Views
317
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock