Search the forum,

Ridgid aluminum pipe wrenches

Post new thread

Discuss Ridgid aluminum pipe wrenches in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
P

PatrykA

I have a few new and used aluminum pipe wrenches if anyone is interested. i have new ones in 10" 12" 14" 18" and 24". I also have a few used ones as well. I have two 36" used aluminum ones and a 48" also. They are used but very well taken care of. I have a used 14" steel ridgid one also. Let me know if interested and I will post up a price. Thanks
 
interested in 36" and a set of 18". can you pm me prices. regards
 
I think this has been posted sometime back as well seem to think prices were not forthcoming for some reason .....but I stand to be corrected.......regards Turnpin:smile:
 
What the hell is the point in coming on here and posting this TWICE! and neither time do you reply to messages or posts. Boring
 
MarkAqua said:
What the hell is the point in coming on here and posting this TWICE! and neither time do you reply to messages or posts. Boring
Click to expand...

Going to pm you, Mark.

Thread closed while Steve and I look into this.
 
Status
Not open for further replies.

Reply to Ridgid aluminum pipe wrenches in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

dreikher
Hole in copper pipe, solder under floor, T coupling & protection
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
208
dreikher
dreikher
S
Advice needed for a mixer Spray for kitchen ?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
153
Lou
Lou
Stigster
Does anyone know the name of this model of Roca toilet?
Hi guys. I'm trying to identify a toilet model before ordering a seat for a customer. I went to what used to be a Roca stockist (they no longer are) and one of the guys there reckoned it might be "The Gap". I went to the new stockist and the guy there disagreed it was "The Gap" and that he'd...
Replies
2
Views
149
Stigster
Stigster
G
UK Moving Pipes Undersink for Dishwasher
Hello I am looking to install a slimline dishwasher (integrated) into a cupboard in my kitchen. The depth of the dishwasher is 550mm and the depth of my cupboard is larger than this. The issue, however, is that the waste pipe which leads from the sink (next door cupboard) comes out quite a...
Replies
22
Views
411
Basher
B
M
Viessmann external flue run conundrum
Hi all. Hope you have all been keeping well. A while back I decided I only wanted to fit one brand of boiler and decided on Viessmann due to space for servicing and changing parts if ever needing to. I am finding my decision rather hard due to the different clearances on flue runs and cupboards...
Replies
9
Views
222
mutley racers
M
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Tile Forum
UK Tiling Forum
Tilezine Tiling News Tile Association
Tiling Advice
Tilers Forum
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock