Discuss Water in Oil Tank in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
J

jackplumb

What is the best way of removing 2" of water from an oil storage tank, without draining 500 litres of oil and cleaning the tank?
 
2m of 15mm copper pipe attached to a hose pipe and syphon into containers. Make sure you dispose of water correctly.
 
I tried that but couldn't suck hard enough, unless the copper was too close to bottom and I couldn't suck. I will try again, thanks for the reply.
 
I have found this to be quite a problem this year and the only practical way of getting it out is with a mechanical pump. I have made myself a rig using my oil transfer pump. Basically on the end of my suction hose I have about 2m of 22mm copper pipe with a 90 degree bend on the end. I connect my suction hose onto this with a jubilee clip and dangle the delivery hose into a 200l open topped barrel. What I then do is suck out and use the copper pipe like a vacuum cleaner, sucking the water from the bottom of the tank, moving the end of the copper pipe over the base of the tank. You will get a lot of oil with it so wait until the barrel contents settle out and you can pump the oil back into the tank and leave the water layer. Remember that the water is contaminated so you need to dispose of properly and charge the customer accordingly.

I find that the usual source of water ingress is from the filling point - over the years with the fuel companies constantly screwing and unscrewing their hoses on it, it tends to work loose allowing rainwater to get around the seal. I re-do them with silicone sealant.
 
Last edited:
those water hogs don't absorb all that much water though, the largest one only just over a litre
 
I tried that but couldn't suck hard enough, unless the copper was too close to bottom and I couldn't suck. I will try again, thanks for the reply.
It is the lift height from the oil to the top of the tank/hose that is the problem. It would be easy to start it syphoning if tank was full of oil. My tip with starting syphoning is to fill the hose with water first from outside tap. This way no risk of oil in your mouth! Do as SimonG said, use a couple metres copper on one end of hose into tank & get the other end as low as possible.
If you are trying to start syphoning by sucking the hose, it would be advisable to use a clear hose & fairly long also. That way you will see the oil flowing & not get any near your mouth.
 
Last edited:
I have found this to be quite a problem this year and the only practical way of getting it out is with a mechanical pump. I have made myself a rig using my oil transfer pump. ....
Will this not wreck your transfer pump eventually? I have one, but try to use it on clean oil if possible & just use the hose & copper pipe syphon method.
 
Water hogs are a waste of time for that amount of water.

No it won't wreck your pump as long as you don't leave it sat full of water after use.
 
Status
Not open for further replies.

Reply to Water in Oil Tank in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

J
Hi Can somebody tell me if a standard heat source pump installation uses a pressurized hot water tank? Or will the pressure for the hot water be...
Replies
1
Views
463
Hello want to know on how do you calculate size of expansion tank for closed heating systems . for example 500 meters of 16mm underfloor heating...
Replies
2
Views
528
For reasons that I won't go into. Is it possible to control the water flow to a cold water header tank without having a ballcock in the header...
Replies
2
Views
184
I’m replacing my single skin plastic oil tank with a new bunded oil tank. I’m going to replace the single 10mm pvc covered oil pipe too, so to...
Replies
3
Views
468
This unit is located in France where they use diesel not kerosene. The feed from the underground tank is not getting through to the boiler. The...
Replies
1
Views
144

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock