Search the forum,

Wanted: Novopress and Rems Jaws/Heads and Slings up to 104mm

Post new thread

Discuss Wanted: Novopress and Rems Jaws/Heads and Slings up to 104mm in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
K

kevpiowuk

Hi, I am looking to buy a Novopress 22mm Head/Jaw
And I also need Rems 22mm Head/jaw and 76, 89 & 104 slings and adaptors
Does anyone have a set of pipe benders on a stand ?

Can anyone help ?

Thank You
 
I also want all of these things!! LOL.

I did miss some cracking bargains on eBay over Xmas. Pick up was in Maidstone not too far from me. I was gutted.
 
keep an eye on e bay a mate just had his stolen so no doubt they will be turning up there soon
 
Hi Danny, IDanny, I am selling my Rems Power press E which will press from 10mm to 108mm fittings. It is only a couple of years old and hasn't had much use. It will only come with 18mm Jaws. You can have it for £300 including postage if its any good to you ? They cost £750 new.
 
Very tempting Kev. I would quite like more jaws than that. Do you know how much they retail at, as I would need a range for domestic plumbing?
 
Hi, Danny, the tongs are on offer from Fast Fix for £75 + vat each up to 35mm which isn't bad. If you buy second hand ones and have them callibrated it would cost that much ?
I will upload a Picture of Rems later
 
Status
Not open for further replies.

Reply to Wanted: Novopress and Rems Jaws/Heads and Slings up to 104mm in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

C
Y Plan, no hot water but heating is working when called
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
277
John.g
J
S
Advice needed for a mixer Spray for kitchen ?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
118
Lou
Lou
M
Viessmann external flue run conundrum
Hi all. Hope you have all been keeping well. A while back I decided I only wanted to fit one brand of boiler and decided on Viessmann due to space for servicing and changing parts if ever needing to. I am finding my decision rather hard due to the different clearances on flue runs and cupboards...
Replies
9
Views
195
mutley racers
M
B
POTTERTON PROMAX 28 COMBI Boiler - Hot Water Issue
Hello, I am seeking some advice, I have a POTTERTON PROMAX 28 COMBI Boiler and I noticed yesterday that the water around the house is no longer warming up. The heat exchanger has been changed 6 months ago, so I do not believe it is that. Does anyone have any ideas on what it could be? Thanks
Replies
4
Views
224
oz-plumber
O
D
Pop quiz, does anyone recognise this radiator valve?
Hi Does anyone recognise the make/brand of the radiator valve. It leaks when closed and Iam hoping I can replace a seal etc?
Replies
3
Views
107
ShaunCorbs
ShaunCorbs
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock