How to Install Grip It Plasterboard Fixings! - Installation Notes

[Billy Bob Bob]

for anyone whos intrested/confused as to what were on about Grip It - Heavy Duty Plasterboard Fixings

 

[lame plumber]

Turning down a freebie?

Who are you, and why are you logged on to Tamz's forum account?

theres some things even a scot will turn down, dog or man sex, shopping with the opposite sex, vegetables etc

 

[Kyle87]

for anyone whos intrested/confused as to what were on about Grip It - Heavy Duty Plasterboard Fixings

Just watched the video.....why was that guy on steps angling a rad!!!! What do you want a rad up there for??

 

[Chalked]

It's a shame no one has made a specific wall plug for dot and dab walls. Say with a brown plug end with a solid bit that would go between the depth of the plasterboard and adhesive to stop the board been compressed.
maybe there is something out there or have I invented something ?

 

[Phil]

Grip It Fixings are a new range of plasterboard fixings on the market, designed to be able to be used on the "dot and dab" plasterboard as well as normal hollow cavity walls. Due to its slim griping wings it is able to open easily with the dab void to produce an effective secure fixing with excellent load bearing capability of up to 180kgs per fixing! excelling any cavity wall fixing currently available! - please see our website for more information!


We have had a few plumbers come back to us with a few issues on how are fixings work and how to install with ease so we thought we would put down a few installation notes:

1) When drilling the holes in the plasterboard:

- Too drill the holes for our fixings we either recommend that you use a "flat drill bit" or a "hole saw" (please use the correct size for the fixing being used) - The use of a twist drill is not recommended due to the tearing effect this produces at the back of the plasterboard, where our fixings arms need to open

2) When inserting the grip it fixings in to the plasterboard:

- Gently tap the fixing in to the plasterboard (we recommend that you insert a screw in the fixing and turn three or four times before tapping the fixing in to ensure that you will not loose the fixing behind the cavity) - Do not apply to much pressure when tapping the fixing in to the plasterboard with a hammer

- To ensure that you have tapped the fixing in at the right depth for the arms to open out, we advise that you use the depth gauge provided (on the depth gauge the 3mm protrusion is for non-plastered walls and the 6m protrusion is for plastered walls)

We recommend before inserting the Grip It Fixing you check for any obstructions that may prevent the locking arms from opening.

---

Like any new product, new installation methods are necessary and once mastered becomes second nature!

If anyone would like to sample our product or for more information please let us know.

Thanks,

Grip It Fixings

Hi Gripitfixings, I do have some free samples and did a small review on here although I was very rushed at the time and maybe didn't give them a proper test. Under what test conditions did you do the 180kg test? Thats over twice my body weight hanging on two little metal wings behind the plasterboard.

I will try them again this week if I get chance, although on site its sometimes easier for me the just cut two stubs of 15mm and insert those in a dot & dab wall against the breeze block and use 3.5" screws. the rad bracket is then fixed solidly to the wall and would be even if all the plasterboard was ripped off around it.

I will give them another go though.

 

[lame plumber]

would anyone honestly hang a boiler off plaster board, a rad is bad enough!

 

[tamz]

It's a shame no one has made a specific wall plug for dot and dab walls.

Spit had one about 20 odd years ago. They might still make them. I have a few kicking about somewhere in the garage as i saw them in the summer when i emptied the place to paint the floor. If i remember where i put them i'll post a pic up.

 

[Sag]

It's a shame no one has made a specific wall plug for dot and dab walls. Say with a brown plug end with a solid bit that would go between the depth of the plasterboard and adhesive to stop the board been compressed.
maybe there is something out there or have I invented something ?

It's been made. Can't remember the name but they are out there. I'll post next time I spot them. No offence to the op but I would much rather fix to the solid blocks behind the plasterboard.

 

[Chalked]

It's been made. Can't remember the name but they are out there. I'll post next time I spot them. No offence to the op but I would much rather fix to the solid blocks behind the plasterboard.

Can you find them?

 

[tamz]

50 Fixing Trade Kit | Holdfast Fixings Ltd | DrylinePro - Heavy Duty Fixing Kit for Dry Line Walls