Search the forum,

Discuss Power flush machines in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

Millsy 82

Plumbers Arms member
Plumber
Gas Engineer
Messages
4,352
I am after a cheap power flush machine. The reason I am after a cheap one is I don't use them a huge amount due to the water around here. So what are half decent?
 
I was contemplating a flush machine but just seems to be no need around the devon area water is nice and dandy i reckon.

IMHO save your hard earned coin
 
I was contemplating a flush machine but just seems to be no need around the devon area water is nice and dandy i reckon.

IMHO save your hard earned coin

It's I've had a couple of open vented oil boilers that I have spent longer flushing than I would power flushing them.
 
I thought kamco were good so I looked at them and thank god I was sat down!
 
Where is Raymondo these days?!

Been thinking the same thing last couple of weeks. Last I remember he was having a hard time with his teeth hope he`s ok and the Squirrel(s) left the new bulbs in the ground this time.
 
He bought a new house recently didn't he? Probably busy with that...
And proberbly working on expanding his empire......p.s hope you and the family are o.k if you are reading this Ray...regards Turnpin:smile5:
 
whose jase?
 
He was funny. I think he may actually have asked to be banned
 
ooo why? or is it a no no

He used to go off on these rants, slagging other engineers and the forum off. It was bizarre and amusing in a car-crash kind of way. Very odd kid really. I met him on a boiler training day. He looked about 12.
 
got a Nordstrom proflush...great machine but wee bit expensive. But liked it better than other ones, Found it gives quicker n better flushes.
 
Status
Not open for further replies.

Reply to Power flush machines in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

We are from Alberta, and I own an electrical company. I have been asked by a BC Mechanical P. Eng. to install an emergency STOP button at the man-door to the boiler room. It's intent is to 'halt' the operation of the boilers in the room should there be an emergency. He is demanding that I do...
Replies
5
Views
304
Hi all Noticed bad smell in my drain out side put my hand down and it unclogged it for now however I checked my sewer drain and after flushing my toilet a good few times nothing is going to the sewer so don't know is there a blockage or what way it works many thanks and advice would be grateful
Replies
3
Views
559
P
  • Question
Boiler is SIRIUS THREE FS 70 Potterton commercial. Situation: We are small building contractors and my labourers managed to damage the radiator pipes during the strip out. Not the end of the world as damages happens. I am responsible builder and paying my bills and to repair the damages if...
Replies
2
Views
81
The left rear floor corner is highest (the shower pan touches/sits on the floor), sloping down diagonally to the front right corner (lowest). The front right corner shim is 5/8", the left front corner is 3/8" shimmed, with shorter shims under left middle and right rear corner. The pan perimeters...
Replies
6
Views
233
I want to reconnect some outbuildings to an existing water supply. The supply pipe is old 22mm MDPE and buried for a fair distance so not going to dig it up and replace it šŸ˜¬. Question is can I use normal 22mm plumbing push-fit connectors to make the connection as finding 22mm MDPE fittings...
Replies
1
Views
296
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock