Search the forum,

Discuss Hot water from cold tap help in the USA area at PlumbersForums.net

Messages
4
Hi I am getting hot water through the cold tap, could this be a TMV problem? TIA
 
Mary,

It could be a couple of things. How hot is the water? You could have a hot pipe under a cold pipe, you could have a mixer tap, that’s getting hot water into it. Any work done recently?
 
Hi I am getting hot water through the cold tap, could this be a TMV problem?
Look for any device (shower, TMV, mixer tap) that mixes hot and cold water. Check the temperature of both inlet pipes (a finger will do). Run the tap-that-should-be-cold until it's coming out hot. Recheck the mixing devices, if one now has both inlet pipes hot that's the culprit. It needs fixing and non-return valves (NRVs) fitted.
 
Look for any device (shower, TMV, mixer tap) that mixes hot and cold water. Check the temperature of both inlet pipes (a finger will do). Run the tap-that-should-be-cold until it's coming out hot. Recheck the mixing devices, if one now has both inlet pipes hot that's the culprit. It needs fixing and non-return valves (NRVs) fitted.
Thanks for your reply, the cold water is getting up to 45 degrees Centigrade. There is a TMV which I have replaced but hasn't solved the problem. I don't have NRV's fitted. It seems from your reply I should try that next. It's not a new installation this problem has occurred recently.
Look for any device (shower, TMV, mixer tap) that mixes hot and cold water. Check the temperature of both inlet pipes (a finger will do). Run the tap-that-should-be-cold until it's coming out hot. Recheck the mixing devices, if one now has both inlet pipes hot that's the culprit. It needs fixing and non-return valves (NRVs) fitted.
Many thanks for your reply, the water is quite hot certainly as hot as the hot tap. I have changed the TMV but this hasn't solved the problem. From your reply I think fitting NRV's is the next thing to do. It's not a new installation this problem had only occurred recently. Thanks for your advice.
[automerge]1597486206[/automerge]
Mary,

It could be a couple of things. How hot is the water? You could have a hot pipe under a cold pipe, you could have a mixer tap, that’s getting hot water into it. Any work done recently?
Hi Thanks for your advice, it's not a new installation but problem that had just occurred. The water is coming out just as hot as the hot tap but in waves of hit then cooler then warm again. I don't have NRV's fitted. I've been advised to fit them do I will try that next. Thanks for your help
 

Reply to Hot water from cold tap help in the USA area at PlumbersForums.net

Similar plumbing topics

  • Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Replies
2
Views
113
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
238
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
6
Views
281
Hi bit of a weird issue, I installed a grohe bathroom tap successfully 2 months ago bought from screwfix. Last week the right hand hot tap makes a squeak noise as I turn it on or off, left tap is 100% perfect and noiseless. This grohe tap is like one unit, so no screw notch or way I can remove...
Replies
1
Views
77
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
94
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock