Search the forum,

Discuss external condensate pipe to sink or not? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Messages
10
I have had some helpful comments elsewhere on how to minimise the chances of the condensate freezing in an external pipe so thanks to all. Trace heating is probably going to be too expensive but I am considering a pump though it doesn't help get to a point internally because of layout.


Because of the siting of the boiler I am going to have a condensate pipe travelling down the external wall and then 500 mm out to a soakaway.


The first choice is to keep it just above the ground for the last 500 mm run out (sloping away from the horizontal) to the condensate trap. Advantages I can see are that the pipe is accessible if it does freeze and I can see if the joint fails at some point in the future (acid leak would be near foundations). Disadvantage is that I get a trip hazard and would have to warn all visitors.


Second choice is to bury the last near horizontal 500 mm a little or even deeper. It is probably less likely to freeze (?) but inaccessible to me if it does (how would you thaw it?). Secondly, if the joint near the house did ever fail would there be any signs I would notice? Would the concrete show it for example?


I have probably had enough disturbed nights and it is hard when you know nothing about plumbing! Does anyone have any answers to my questions to help me make a decision?


Thank you in advance
 
I always use condensulate xtreme for external condensate runs, you have to run it in 1 1/2 pipe and use swept elbows but it won't freeze until it's below -20 which doesn't happen to often in the UK.

I would bury the soakaway pot 500mm away from the property and no less than 500mm from the surface to the top of the pot, no good the pipe not freezing if the pot is frozen solid.

3/4 fill the pot with lime stone chipping, make sure you leave an air gap between the pipe and the chipping.

 
Last edited:
I always use condensulate xtreme for external condensate runs, you have to run it in 1 1/2 pipe and use swept elbows but it won't freeze until it's below -20 which doesn't happen to often in the UK.

I would bury the soakaway pot 500mm away from the property and no less than 500mm from the surface to the top of the pot, no good the pipe not freezing if the pot is frozen solid.

3/4 fill the pot with lime stone chipping, make sure you leave an air gap between the pipe and the chipping.


had that freeze last winter, thought it was 11/2 waste at first then cut into it to find that :D
 

Reply to external condensate pipe to sink or not? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello all, I'm would like to extend an existing outside tap to another point in the garden. I'm about to pour a concrete patio and was hoping to run the water line underneath. There are existing drain (and who knows what) pipes running along the same wall so I'm nervous about digging too far...
Replies
6
Views
227
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
115
Hello all, I’m replacing a concrete paving slab patio in the back yard. The original patio used 50mm deep concrete slabs on hardcore & sand. I’m planning to pour a 100mm deep concrete patio on 100mm hardcore. In order to achieve the same final height to line up with the rest of the patio, I...
Replies
6
Views
231
Copper pipes, I think its fair to say, is not what it used to be, the copper is getting thin while the cost is going up. Meanwhile, plastic Pushfit seems to be getting better and better, cost and convenience was always better, but now the quality is to, have we reached a stage where plastic will...
Replies
2
Views
242
I want to reconnect some outbuildings to an existing water supply. The supply pipe is old 22mm MDPE and buried for a fair distance so not going to dig it up and replace it 😬. Question is can I use normal 22mm plumbing push-fit connectors to make the connection as finding 22mm MDPE fittings...
Replies
1
Views
263
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock