Search the forum,

Discuss external condensate pipe to sink or not? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Messages
10
I have had some helpful comments elsewhere on how to minimise the chances of the condensate freezing in an external pipe so thanks to all. Trace heating is probably going to be too expensive but I am considering a pump though it doesn't help get to a point internally because of layout.


Because of the siting of the boiler I am going to have a condensate pipe travelling down the external wall and then 500 mm out to a soakaway.


The first choice is to keep it just above the ground for the last 500 mm run out (sloping away from the horizontal) to the condensate trap. Advantages I can see are that the pipe is accessible if it does freeze and I can see if the joint fails at some point in the future (acid leak would be near foundations). Disadvantage is that I get a trip hazard and would have to warn all visitors.


Second choice is to bury the last near horizontal 500 mm a little or even deeper. It is probably less likely to freeze (?) but inaccessible to me if it does (how would you thaw it?). Secondly, if the joint near the house did ever fail would there be any signs I would notice? Would the concrete show it for example?


I have probably had enough disturbed nights and it is hard when you know nothing about plumbing! Does anyone have any answers to my questions to help me make a decision?


Thank you in advance
 
I always use condensulate xtreme for external condensate runs, you have to run it in 1 1/2 pipe and use swept elbows but it won't freeze until it's below -20 which doesn't happen to often in the UK.

I would bury the soakaway pot 500mm away from the property and no less than 500mm from the surface to the top of the pot, no good the pipe not freezing if the pot is frozen solid.

3/4 fill the pot with lime stone chipping, make sure you leave an air gap between the pipe and the chipping.

 
Last edited:
I always use condensulate xtreme for external condensate runs, you have to run it in 1 1/2 pipe and use swept elbows but it won't freeze until it's below -20 which doesn't happen to often in the UK.

I would bury the soakaway pot 500mm away from the property and no less than 500mm from the surface to the top of the pot, no good the pipe not freezing if the pot is frozen solid.

3/4 fill the pot with lime stone chipping, make sure you leave an air gap between the pipe and the chipping.


had that freeze last winter, thought it was 11/2 waste at first then cut into it to find that :D
 

Reply to external condensate pipe to sink or not? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hi everyone I hope you can help. We were getting some work done and our builder attached the boiler condensate pipe to the sink waste pipe. This was all then covered with dot and dab. Shown in the picture, red arrow. So the only thing visible now is a round pipe from the wall. We are yet to fit...
Replies
5
Views
319
Hello I have a condensate pipe that appears to be leaking at the joint. How do I fix the leak? Would something like plumbers putty around the joint work or does it need to be some other compound? Can I simply pull the pipe and joint out and then put the compound round it Thanks
Replies
4
Views
501
Engineer has installed several boilers for me. All the condensate pipes have been connected externally into soil stack or rain water downpipe. In each case he just drilled a hole in the pipe, and stuck the condensate in the side, smeared glue everywhere. No boss, or branch. Is this allowed, is...
Replies
2
Views
526
[ASIDE: I did wonder if this was the best forum for this but figured as it was a boiler related issue that the gas engineers would be dealing with it as a matter of course. If I'm wrong can someone let me know and I'll shift it to a better place.] I have a condensing boiler installation...
Replies
5
Views
215
Hi, I am probably being unduly paranoid here but I noticed under our kitchen sink that there is some corrosion evident on a small section of copper pipe between compression fittings on the hot water feed. There are take offs for an outside hot and cold tap together with isolation valves and...
Replies
9
Views
239
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock