Search the forum,

Discuss reliance mixers in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
A

azza100

reliance universal 4 in 1 mixers, new compression type, open to offers
thanks for looking
 
have you a mobile you can send them to i have no idea how to upload pics onto here, im not the best with computers ha
 
waiting for new replacement phone, was dropped into manhole and lost still in dispute with
insurance co. as to wether its covered [yes I know its covered in s**t]may have to see if one of the kids has an old one for time being:)regards turnpin ps any model number?
 
they're the heatguard dc3 universal 4 in 1 thermostatic mixer and i have 5 of them, the part numbers HEAT 170 035, bad luck about the phone though i go through them like nobodys business at work!! the boxes are just dented and a bit dirty from being on the back of the van and two of them are water damaged so will have to be sent in different packing
 
waiting for new replacement phone, was dropped into manhole and lost still in dispute with
insurance co. as to wether its covered [yes I know its covered in s**t]may have to see if one of the kids has an old one for time being:)regards turnpin ps any model number?

Buy a pay as you go phone for under £20 at a super market or car phone ware house. Make sure you buy one thats on the same network as your contract phone. Take the SIM out and put it in the new pay as you go and you're up and running again for £20. Voice of experience here. It doesn't help having no blower when most of your work comes in via it!
 
ditto, ive just had to buy a new phone purely because half the time it decides it doesnt want to take calls
 
Buy a pay as you go phone for under £20 at a super market or car phone ware house. Make sure you buy one thats on the same network as your contract phone. Take the SIM out and put it in the new pay as you go and you're up and running again for £20. Voice of experience here. It doesn't help having no blower when most of your work comes in via it!

waiting for new replacement phone, was dropped into manhole and lost still in dispute with
insurance co. as to wether its covered [yes I know its covered in s**t]may have to see if one of the kids has an old one for time being:)regards turnpin ps any model number?

awaiting new sim card with my original number as sim was lost with phone see original post assured it is in the post but maybe delayed due to weather still arguing about replacement phone though:(regards turnpin
 
i have tried to get photos up, im blaming the computer, will see if the girlfriend can do it on her camera tomorrow as shes used to it with all the facebook stuff
 
Hi azza100 dont worry too much have now checked them on web waiting for payment for some work done 3 weeks ago will hopefully be in touch in the near future to make an offer looking like it will be after christmas if my dosh comes through:)regards turnpin
 
Last edited:
Status
Not open for further replies.

Reply to reliance mixers in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Recently had a Viessmann Vitodens combi boiler installed, quite often when the adjacent cold mixer tap is opened the boiler starts for a few seconds! Can anyone tell me what is causing this? And how to cure?
Replies
3
Views
200
IS IT POSSIBLE TO ADJUST THIS MIXER UNIT? WE HAVE TO HAVE IT TURNED ALMOST FULLY ANTI CLOCKWISE TO GET HOT WATEROUT. THE FRONT PLATE WITH MIRA ON IT PRISES OFF AND INSIDE THERE ARE SOME PLASTIC BITS AND A SMALL CROSS-HEAD SCREW IN THE MIDDLE. THANKS
Replies
6
Views
224
Our kitchen mixer tap has started dripping. Like so much of the plumbing in our almost new build bungalow, it is lacking! The plumber didn't install any isolating cocks in the H&C feed to the tap so how can I identify which of the valves is passing? Shut the whole H&C water system down?
Replies
12
Views
324
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
1
Views
195
Hi. I need a new toilet supply line but don’t know the size type of the fitting at the shut off valve. It is not 3/8 compression. It is a plastic nut about the same size as the one going into the cistern but has a different thread. Attached is a photo. Can you advise. Thanks.
Replies
2
Views
183
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock