You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
inlet
An inlet is an indentation of a shoreline, usually long and narrow, such as a small bay or arm, that often leads to an enclosed body of salt water, such as a sound, bay, lagoon, or marsh.
What should be a simple job is causing me no end of problems. Single urinal leaking constantly into the bowl. changed the syphon and its still doing the same, ive now tried another syphon and its still doing it. Works properly some times but then seems to syphon very slowly, if I turn the water...
Hey all, I've just been having a play with the Let-by and tightness test feature on my evo3. Is there some special way to get the pressure to be 10 and 20mb?
I cannot seem to get the correct reading. It's either slightly higher or lower.....
Hi there this is probably one of those posts which will have all of you experts scratching your heads thinking 'we've got a right one here' but it's a problem that has been ongoing for a number of months because I'm not that confident about DIY and always worry I'm going to make matters worse by...
Bluesman
Thread
bottom
cistern
dripping
inlet
leak
pipe
valve
water
where
hi
Does anyone the correct way (i.e. that building control will accept?) of blocking off a disused inlet inside a plastic inspection chamber. I have removed the downstairs loo from my house and wish to cap of the inlet inside the chamber. I know that you can buy caps that can be fitted on to...
terry1952
Thread
block
chamber
house
inlet
inside
inspection
outside
Hi,
This one should be relatively straightforward for someone who knows there way around these Geberit flushes....
I have attached 2 pictures - one of the system and one of the jet of water.
hxxp://1drv.ms/1qxtOz3
hxxp://1drv.ms/1ubSBxs
Can't figure out how to attach...
These usually come with one end straight and the other bent.
Does anyone know which one goes to the back of the machine and why?
Seemingly a simple question but interested to see how many differing opinions come back ;)
I have just installed this boiler. Nice fancy user interface. In service mode in max rate I am getting
O2 4.2
co2 9.5
Co ppm 129
Ratio .0013
Ratio and co is quite high. Usually when commissioning a new boiler I get a ratio of around .0007 and about 70 ppm co.
Pipe...
Hi guys in new here.I've just bought my first home and I've got the point of fitting the washing machine.I can't open the tap once the inlet pipe is fastened in place.I tried opening it after turning the water off then fitting the pipe but then I can't fasten the pipe on enough to get it to seal...
toboy
Thread
inlet
machine
pipe
tap
washing
washing machine
won't
I'm trying to fit a new close couple toilet. The inlet is a threaded 15mm pipe and I'm struggling to find the right connection to hook it up to 15mm pipe. I tried flexible hose with a half inch connector but it doesn't fit. The only other imperial sizes seem too big or small. I must be missing...
Probably a long shot but does anyone know what make this valve is?
http://www.doityourself.com/forum/attachments/toilets-sinks-showers-dishwashers-tubs-garbage-disposals/15419d1374419916-toilet-cistern-without-ballcock-not-shutting-off-water-inlet-toiletcistern1.jpg
This is just a picture of...
OK I give up, I've spent ages looking for this but can't find one. A chrome shower head with a nozzle or head that can be angled in different directions but which also has a bottom inlet for surface mounted pipework. Any suggestions please post details.
Thanks
ma701ss
Thread
150mm
adjustable
bottom
head
inlet
mounted
shower
shower head
spray
surface
Does anyone know of a standard central heating radiator which will take a heating element (of the sort used on towel rail radiators). I know there used to be radiators where the inlet/outlet went straight into the (slightly rounded) bottom of the radiator but all I can find now are...
Terry Goodison
Thread
central heating system
cold radiator
dual
dual fuel
hot rads
inlet
radiator
radiators
Hi.
I have recently replaced a single panel radiator (without any fins) of size approximately 1200 x 600. This radiator is within the family bathroom and connected to a single pipe system. The pipe size is approximately 2 1/2" steel design. This radiator is the first on the loop and connected...
Canyondust
Thread
attach
bottom
column
inlet
pipe
problem
radiator
right
single
single pipe system
system
Hi there,
This inlet valve is playing up and filling very slowly. I'm guessing there's something blocking it or a washers gone or something, but I am unable to either open up the unit or remove it from the stem. I wanted to find out what model and brand it is to try and understand what I'm...
I have a 24 kw ecotec pro on a 22 mm 8 metre run on it which has fluctuating inlet pressure. Goes from 18mb and then suddenly drops down to 10 and back up again. It has a cooker and fire connected onto it after this section but it is the same with and without them on it. All fine at the meter...
I have found. Leak on my toilet inlet the plastic bit that mets the isolation valve so decided to change the valve. Problem is now I can't get a water tight seal form where the plastic meets the valve. I have done everything but no luck.
any ideas' flexible hose?
Ok, so here's my situation. I have a cold water tank stored on a 2m high tower, which is on top of my roof of my 2 storey house.
The cold water tank has an "in" pipe, coming from the city supply which fills it up.
This has been fine for the past few years (house and all plumbing stuff is about...
brainii
Thread
house
inlet
noise
pressure
roof
tank
vibrating
washer
water
water tank
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.