Search the forum,

Can anyone identify this tap please

Post new thread

Discuss Can anyone identify this tap please in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
P

Paul Cockhill

Messages
293
Hi

Can anyone identify this tap please. I think it is a Franke but cannot find any marking on it. It has a persistent drip. The lever on the front allows filtered water through the tap and it is this that is causing the problem. If I can identify the tap then I might be able to get a spare part.

Thanks

Paul
 

Attachments

  • 2017-01-31 11.37.12.jpg
    2017-01-31 11.37.12.jpg
    98.7 KB · Views: 83
The spout and the handles look very similar to an Ikea tap I replaced a few months ago.

It didn't have the filtered tap, bit everything else looks the same.

Might be worth a try
 
Hi Paul,

I am not to sure either but would think it's either franke or Italien Brand - Perrin & Rowe Metis Triple Lever Pewter Sink Filter Tap & Rinse 1580PF

Id try asking showerdoc.com and send them a couple of pictures they may can help you to figure out what brand it is. But looks very similar to the Italian one.
 
Brita tap from the brita water filter company
 

Attachments

  • 20161129_145338.jpg
    20161129_145338.jpg
    89 KB · Views: 37
Last edited:
Don't know the tap, but there might be a small grub screw at the back?
Spout pulls out?, the collar as well? or might unscrew?, might have access to gubbins inside? which might be more identifiable?
But then merchant may say, "They've gone bust you'll have to replace it".
 
This really IS my bag...
Fact is it could be any make. Best to take either the hot or cold handle and shroud off and measure the dimensions of the cartridge then post them here or send me a message and I'll let you know where to get a replacement. If you want to know what to measure go to our website.
THIS is why I invented TapMedic :cool:
 
YorkshireDave said:
This really IS my bag...
Fact is it could be any make. Best to take either the hot or cold handle and shroud off and measure the dimensions of the cartridge then post them here or send me a message and I'll let you know where to get a replacement. If you want to know what to measure go to our website.
THIS is why I invented TapMedic :cool:
Click to expand...
Hi thanks for posting here. :)

Go steady on the free plugs if you don't mind. And give us a shout if you want some information regarding forum sponsorship.
 
Status
Not open for further replies.

Reply to Can anyone identify this tap please in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

S
Advice needed for a mixer Spray for kitchen ?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
157
Lou
Lou
C
How to identify dripping tap.
Our kitchen mixer tap has started dripping. Like so much of the plumbing in our almost new build bungalow, it is lacking! The plumber didn't install any isolating cocks in the H&C feed to the tap so how can I identify which of the valves is passing? Shut the whole H&C water system down?
Replies
12
Views
374
Timmy D
T
R
squeaky grohe bathroom tap 2 months old
Hi bit of a weird issue, I installed a grohe bathroom tap successfully 2 months ago bought from screwfix. Last week the right hand hot tap makes a squeak noise as I turn it on or off, left tap is 100% perfect and noiseless. This grohe tap is like one unit, so no screw notch or way I can remove...
Replies
7
Views
275
Raff
R
P
Repeated Airlock in Bathroom
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
365
Chuck
C
jamespipe
Plumber recommendation for heat pump HWS installation
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
6
Views
314
oz-plumber
O
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Contractor Forum
Tiling Forums UK
UK Tiling Forums
Tile Blog
Tiling Tools
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock