Discuss Thread sealants in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

magicno1

Gas Engineer
Messages
252
I have a few shower arms and concealed bath and basin spouts to do. Over the years I have done quite a few. Have been looking at Loctite thread sealants and was wondering if any of you use them and what number sealant you use. There seems to be loads of different number ones!

cheers all
 
Loc 577
 
[DLMURL="http://advancedadhesivesshop.co.uk/epages/10af3860-b08b-4deb-a7ad-c88fe8542800.sf/en_GB/?ObjectPath=/Shops/10af3860-b08b-4deb-a7ad-c88fe8542800/Products/7"]Loxeal 58-11 75ml - Advanced Adhesives[/DLMURL]
 
Last edited by a moderator:
[DLMURL="http://advancedadhesivesshop.co.uk/epages/10af3860-b08b-4deb-a7ad-c88fe8542800.sf/en_GB/?ObjectPath=/Shops/10af3860-b08b-4deb-a7ad-c88fe8542800/Products/7"]Loxeal 58-11 75ml - Advanced Adhesives[/DLMURL]

Looks good but trust loctight
 
Last edited by a moderator:
[DLMURL="http://advancedadhesivesshop.co.uk/epages/10af3860-b08b-4deb-a7ad-c88fe8542800.sf/en_GB/?ObjectPath=/Shops/10af3860-b08b-4deb-a7ad-c88fe8542800/Products/7"]Loxeal 58-11 75ml - Advanced Adhesives[/DLMURL]

Say`s you have to leave it 24hrs just like the 577, I never have 24hrs to wait.
 
Last edited by a moderator:
Used to have a producer similar to loxseal called Cimberio. Same color and make up of Loctite. Brilliant stuff for tails in towel rails, garden taps etc. used it on a bib tap, screwed it in and left it 30 min and bingo! Can't get the stuff now.
Think I'll look at the 577.
Is the 577 ok on brass?
 
This has been discussed many times

It is loctite 577 for every threaded connection
 
Used to have a producer similar to loxseal called Cimberio. Same color and make up of Loctite. Brilliant stuff for tails in towel rails, garden taps etc. used it on a bib tap, screwed it in and left it 30 min and bingo! Can't get the stuff now.
Think I'll look at the 577.
Is the 577 ok on brass?

On everything except plastic
 
Does anybody bother with the cleaner for 577 as shown in their video?

Nope if it's dirty just get a rag other than that I've done nothing special
 
Status
Not open for further replies.

Reply to Thread sealants in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I'm at the stage of my shower replacement where I have a new shower head to screw into the wall pipes. I tried it, turned on the shower, and find...
Replies
3
Views
200
In short: Do suppliers sometimes list BSPT as BSP? I need a tee, 22mm each end with a BSPT in the middle for an expansion vessel to dangle from...
Replies
2
Views
384
Hi all, My partner and I recently bought a house and have been attempting to make the bathroom less fugly. I was removing the bath and shower...
Replies
6
Views
697
Hi I have installed my concealed shower valve and fitted wall panels, I'm soon ready to put shower fittings through the panels and screw them into...
Replies
12
Views
2K
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two...
Replies
2
Views
241
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock