Today's install.

Post new thread

Discuss Today's install. in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
Whn1

Whn1

Plumbers Arms member
Plumber
Gas Engineer
Messages
1,331
Guess the missing boiler...... ;) ImageUploadedByTapatalk1361296846.427556.jpg
 
Hopefully not, there's spacers on the clips and they're spaced apart. Got me worried now ;)
 
Last edited:
It's a shame to cover good copperwork, it's better than 99% of the so called art out there.
 
Haha first I was a plumber, second a heating engineer and now an artist.
 
Nice neat job.
If you've used the wee Talon spacers, you'll get foam insulation around the pipework without too many problems. Use tie wraps to bind it nice and tight.
 
PlumbersMate said:
Have to say mate your work is the absolute dogs ********. Teach me please lol
Click to expand...

plumbersmate. this ain't rocket science,
first you need teaching, then a g3 cert,
and then do it how you want to see it in your own house,
if your not happy take it out and start again.
forget about the money,a good job is what it is all about.
a nice tidy job, a safe install, and a happy customer,life's sweet.
 
system3 said:
Nice neat job.
If you've used the wee Talon spacers, you'll get foam insulation around the pipework without too many problems. Use tie wraps to bind it nice and tight.
Click to expand...
I only started using them about a year ago, make jobs where you have to lag so much easier.
 
Whn1 said:
I only started using them about a year ago, make jobs where you have to lag so much easier.
Click to expand...
They also save bending crossovers if you use 2 spacers on a clip as the pipe will then pass right over the other one without touching it.
 
Yea haha it's crossed my mind but I might end up going a bit crazy! Like using 6 stacked up to pass over the pass overs :)
 
c'mon!!!

admit it, you get paid by the hour dont you?.

bet you get lunch breaks too!!.lol
 
Standard day rate redsaw, paye all the way.
 
Nice work, have you measured where the guttering stops outside ?
 
well done you are almost good as me :)pmsl
You have had lots of time to pull all this bends and how is the insulation going in !?
well done good job
 
I'm a pro, everything mentioned has been catered for. Even the immersion. I don't think the pictures are doing the spacing justice. ;)
 
Wouldn't know anything about that.......
 
Nice work pal.................. that coil will be a biatch to bleed even on a sealed system, due megaflos coil in coil construction, unless i have missed the AV?

Flue must be close to soffit?
 
half a mornings worth of work there plenty space to work in unlike the one i done today ,
agree with vern cant see aav nor low level doc??
 
Nice job ,, Can't see the balance valve on the cylinder return , !!!
 
vern said:
Nice work pal.................. that coil will be a biatch to bleed even on a sealed system, due megaflos coil in coil construction, unless i have missed the AV?

Flue must be close to soffit?
Click to expand...

Was just going to put vent on top of boiler, do megaflow specify otherwise?
flue easily clears gutter/ soffit. The drawing is a rough outline.

We'll see for sure tomorrow, it's changeover day.
 
Doc is on flow into cyl. Corrrr ou lot are hard work...
 
fair play to you for putting your work on here knowing what this mob is like !!!

Did you wipe your joints off or are they all green today?
 
hammers4spanner said:
fair play to you for putting your work on here knowing what this mob is like !!!

Did you wipe your joints off or are they all green today?
Click to expand...

Anyone got a noose I can borrow?
 
Lovely install! Is that an open end left on a gas pipe?!....

And I'd guess at a Worcester ri boiler!
 
APPlumbing said:
Lovely install! Is that an open end left on a gas pipe?!....

And I'd guess at a Worcester ri boiler!
Click to expand...


It is but a future gas pipe, open both ends, the clients using the original boiler which is being moved from one end of the house to the other, so all the pipes are in place for the changeover.
 
And all wrong on the boler guesses. :)
 
Whn1 said:
Was just going to put vent on top of boiler, do megaflow specify otherwise?
flue easily clears gutter/ soffit. The drawing is a rough outline.

We'll see for sure tomorrow, it's changeover day.
Click to expand...

yep should have one on coil flow pal, all covered in MI's
 
I reckon its a Chaffoteaux Challenger that he has been saving for that "special" job.
 
New posts
Status
Not open for further replies.

Reply to Today's install. in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

O
    • Like
Shower install advice
After some advice please. Recently bought some shower panels to have installed. However the installers must have missed installing the waterproof...
Replies
2
Views
364
CharlesMatthew
C
M
Installing pipework to avoid airlocks
How it best to install pipework to best avoid airlocks with gravity hot water. Install level or slightly down hill in direction of flow? Thanks
Replies
1
Views
186
fowlerboi
F
T
Ecostat S - unsecured temperature knob
Hi All, The temperature knob on my Hansgrohe Ecostat S shower mixer has been installed insecurely and is loose when pulled, I've looked at the...
Replies
2
Views
241
Tailpond
T
jamespipe
Plumber recommendation for heat pump HWS installation
Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't...
Replies
6
Views
369
oz-plumber
O
A
    • Like
  • Locked
Combi Boiler Install in Devon, Exeter.
Hi, I recently fitted a new central heating circuit and ran hot and cold to the bathroom and kitchen in my property (I was a CORGI registered...
Replies
0
Views
497
Aaron111
A

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock