Today's install.

[Whn1]

Guess the missing boiler......

 

[SimonG]

Very nice work.

Be a bugger to insulate

 

[Whn1]

Hopefully not, there's spacers on the clips and they're spaced apart. Got me worried now

 

[SimonG]

It's a shame to cover good copperwork, it's better than 99% of the so called art out there.

 

[Whn1]

Haha first I was a plumber, second a heating engineer and now an artist.

 

[sam51]

nice tidy install there mate.
wannabe plumbers take note.

 

[PlumbersMate]

Have to say mate your work is the absolute dogs ********. Teach me please lol

 

[Guest123]

Nice neat job.
If you've used the wee Talon spacers, you'll get foam insulation around the pipework without too many problems. Use tie wraps to bind it nice and tight.

 

[Whyme]

Niiiice, Boiler erm a ferroli..

 

[sam51]

Have to say mate your work is the absolute dogs ********. Teach me please lol

plumbersmate. this ain't rocket science,
first you need teaching, then a g3 cert,
and then do it how you want to see it in your own house,
if your not happy take it out and start again.
forget about the money,a good job is what it is all about.
a nice tidy job, a safe install, and a happy customer,life's sweet.

 

[Whn1]

Niiiice, Boiler erm a ferroli..

That'd ruin any install!

 

[Whn1]

Nice neat job.
If you've used the wee Talon spacers, you'll get foam insulation around the pipework without too many problems. Use tie wraps to bind it nice and tight.

I only started using them about a year ago, make jobs where you have to lag so much easier.

 

[Guest123]

I only started using them about a year ago, make jobs where you have to lag so much easier.

They also save bending crossovers if you use 2 spacers on a clip as the pipe will then pass right over the other one without touching it.

 

[Whn1]

Yea haha it's crossed my mind but I might end up going a bit crazy! Like using 6 stacked up to pass over the pass overs

 

[REDSAW]

c'mon!!!

admit it, you get paid by the hour dont you?.

bet you get lunch breaks too!!.lol

 

[Whn1]

Standard day rate redsaw, paye all the way.

 

[Kev the gas]

Nice work, have you measured where the guttering stops outside ?

 

[wheeto]

Nice work, have you measured where the guttering stops outside ?

Ha ha that's going to be the second thing to get him worrying in this thread!

Nice pipework though.

 

[SafeGasInstall]

well done you are almost good as me pmsl
You have had lots of time to pull all this bends and how is the insulation going in !?
well done good job

 

[SafeGasInstall]

and dont get me wrong but i hope is not me who is going to change the immersion one day

 

[Whn1]

I'm a pro, everything mentioned has been catered for. Even the immersion. I don't think the pictures are doing the spacing justice.

 

[sam51]

I'm a pro, everything mentioned has been catered for. Even the immersion. I don't think the pictures are doing the spacing justice.

i thought the only pro"s in london were in soho lol.

 

[Whn1]

Wouldn't know anything about that.......

 

[vern]

Nice work pal.................. that coil will be a biatch to bleed even on a sealed system, due megaflos coil in coil construction, unless i have missed the AV?

Flue must be close to soffit?

 

[hammers4spanner]

half a mornings worth of work there plenty space to work in unlike the one i done today ,
agree with vern cant see aav nor low level doc??

 

[vern]

nor low level doc??

I missed that too!

 

[mutley racers]

doc? drain of cock?

 

[E4gas]

Nice job ,, Can't see the balance valve on the cylinder return , !!!

 

[hammers4spanner]

lol turning into pick a fault this , flue's probably termining into neighbours window lol

 

[Whn1]

Nice work pal.................. that coil will be a biatch to bleed even on a sealed system, due megaflos coil in coil construction, unless i have missed the AV?

Flue must be close to soffit?

Was just going to put vent on top of boiler, do megaflow specify otherwise?
flue easily clears gutter/ soffit. The drawing is a rough outline.

We'll see for sure tomorrow, it's changeover day.