Wiring s plan from old set up y plan...?

[Notagainpike]

No greys are perm live

Your live from the prog for heating goes to the room stat and then to the brown on the port valve

Sleeve donates a switched live...yes??

 

[ShaunCorbs]

Sleeve donates a switched live...yes??

Depends on colour brown live blue neutral etc

 

[Deleted member 120897]

I have

So to clarify:

At motorised valves you have a permanent 240 live on grey, 240 on orange and 240 on brown when calling?

 

[Notagainpike]

This was how it was on y plan...

 

[Notagainpike]

Depends on colour brown live blue neutral etc

Red sleeved brown

 

[Notagainpike]

So to clarify:

At motorised valves you have a permanent 240 live on grey, 240 on orange and 240 on brown when calling?

Yeah...

 

[Notagainpike]

This was how it was on y plan...

 

[Deleted member 120897]

Are those white wires still connected? Can you post a decent photo of those Wago connectors?

 

[ShaunCorbs]

Your missing something as the pump would run

 

[Notagainpike]

No greys are perm live

Your live from the prog for heating goes to the room stat and then to the brown on the port valve

Yes, sorry, my greys are fed from perm live, which also feeds the prog.
Output from the prog. For heating, goes to nothing currently!!!

 

[Notagainpike]

Black on 10 i believe is hw out from prog.

 

[ShaunCorbs]

Time for a rewire and start from scratch bell the existing cables out to see what you’ve got down stairs and adjust in the box to match

 

[Notagainpike]

Time for a rewire and start from scratch bell the existing cables out to see what you’ve got down stairs and adjust in the box to match

Hope you guys arnt busy tonight...

 

[ShaunCorbs]

Just follow the picture I sent etc eg you will be fine

 

[Notagainpike]

Are those white wires still connected? Can you post a decent photo of those Wago connectors?

So, i think its all right,
I have my browns to the blue, and red,
Which run back up to the out puts from cylinder stat and room stat..

 

[Notagainpike]

So, i think its all right,
I have my browns to the blue, and red,
Which run back up to the out puts from cylinder stat and room stat..

 

[ShaunCorbs]

So turn the heating on prog should give you 240 to the room stat

Turn the room stat up you should have 240v on the 2 port brown and the 2 port lever should go slack

Correct ?

 

[Notagainpike]

So turn the heating on prog should give you 240 to the room stat

Turn the room stat up you should have 240v on the 2 port brown and the 2 port lever should go slack

Correct ?

Il check after my scampi and chips
Just now, i called for hw, time i got to boiler, pump was running, boiler screen was live, but not lit up, boiler wasnt firing, cover off valve, lever had moved and pressing switch, pulled supply to brown, pump stopped, lever released, boiler screen shut down...

 

[Murdoch]

NB the colours of the cables except from the zone valves could be misleading to say the very least.

I recommend you confirm all the connections

does your boiler need PL and SL ?

 

[ShaunCorbs]

NB the colours of the cables except from the zone valves could be misleading to say the very least.

I recommend you confirm all the connections

does your boiler need PL and SL ?

Yes 330 does need both

 

[Murdoch]

Yes 330 does need both

I suspect the OP doesn’t understand this

 

[Notagainpike]

I suspect the OP doesn’t understand this

The op is not as dumb as you may think

 

[Notagainpike]

Right then....
Many thanks to all that helped. Much aporeciated...

Its only bloody fired

 

[Notagainpike]

Im not sure tbh. What happened. I took front off boiler, messed with the sensors on flow and return, i took the cover off the board, removed it, contact spray and cleaned all connectors, found a couple of small areas of corrosion, reassembled.
Re bled rads, bled the air valve on the hw coil return.
It fired on hw demand.

Going to let it run and warm for a bit. Then try the hot water side of things...
May not be home and dry yet, but its progress.
Again many thanks for all your help.