Which way round should the filling loop be fitted?

[AWheating]

Typical gas man !!! , bet he would get all upset if we suggested installing push fit ball-o-fix on gas supply to his boiler !!

come on, it should be a push fit lever valve to avoid pressure loss

 

[chris watkins]

BORING, I thought this question was done to death a few months ago :-/

Sorry was not here then, but your right BORING !!! (although it does tell you how much notice / information this lot take on board if it is just that sort time ago LOL.)

 

[ggman]

What a mess, I have the same filling loop as diamond gas , the valve in this one as well, following the directional arrows will be fitted on the heating side, not big problem the valve can be easily reversed and fitted on the water main , my concern is the little Iso valve, it may had to fitted with the arrow pointing out of the CH side, any opinion?

 

[Barry98]

Check valve is always fitted to the cold main side. If MI state different then you need to also comply with the water regs so need to fit an additional double check on the cold main. So it will cost your more if you follow MI in this instance.

Some chemicals can be dosed via the filling loop so having the check on the heating side wont protect the cold from contamination.

Happy birthday Bod

Cheers aw

 

[casaco]

BORING, I thought this question was done to death a few months ago :-/

Sorry to bore you mountain man, but I did try and look back over old posts before I placed mine. Unfortunately I couldn't find the answer I was looking for. Guess what, despite all the replies I have had so far, I still can't decide which way the loop should be fitted.
If the check valve fails in any position there will be a risk of contamination, don't forget some loops only have 1 iso valve attached to the check valve, so much for water regs then.

 

[mountainman]

Sorry to bore you mountain man, but I did try and look back over old posts before I placed mine. Unfortunately I couldn't find the answer I was looking for. Guess what, despite all the replies I have had so far, I still can't decide which way the loop should be fitted.
If the check valve fails in any position there will be a risk of contamination, don't forget some loops only have 1 iso valve attached to the check valve, so much for water regs then.

Exactly why the subject is boring, too many conflicting replies to be of any help.
Traditionally there is one iso and one check valve with a flexible loop.
The loop should only be connected whilst filling the system then removed.
No chance of cross contamination then.

 

[diamondgas]

Sorry to bore you mountain man, but I did try and look back over old posts before I placed mine. Unfortunately I couldn't find the answer I was looking for. Guess what, despite all the replies I have had so far, I still can't decide which way the loop should be fitted.
If the check valve fails in any position there will be a risk of contamination, don't forget some loops only have 1 iso valve attached to the check valve, so much for water regs then.

My take in this is that the check valve is to protect the mains water and therefore any water leaving the mains to enter the heating must first travel through the 'protection barier' formed by the check valve! That way there's no way contamination can get back through except if the valve fails!

That's probably been said already, but there ya go

 

[Backboiler]

BORING, I thought this question was done to death a few months ago :-/

It is wrong to assume that all members have the time or patience to trawl prior posts in search of an answer. Occasionally topics can be difficult to locate depending on search tags, and don’t forget when you are under pressure you may need a quick answer. Even you are guilty of your perceived monotony. I note you requested help recently on an area which was addressed in 2010 (here are the links). A little searching around the forum may have helped? We are not all experts in all areas which is the reason we come on here; to learn and impart knowledge on others.
http://www.ukplumbersforums.co.uk/central-heating-forum/36710-ideal-isar-noisy.html

http://www.ukplumbersforums.co.uk/central-heating-forum/13456-ideal-isar-he-24-banging.html

 

[mountainman]

It is wrong to assume that all members have the time or patience to trawl prior posts in search of an answer. Occasionally topics can be difficult to locate depending on search tags, and don’t forget when you are under pressure you may need a quick answer. Even you are guilty of your perceived monotony. I note you requested help recently on an area which was addressed in 2010 (here are the links). A little searching around the forum may have helped? We are not all experts in all areas which is the reason we come on here; to learn and impart knowledge on others.
http://www.ukplumbersforums.co.uk/central-heating-forum/36710-ideal-isar-noisy.html

http://www.ukplumbersforums.co.uk/central-heating-forum/13456-ideal-isar-he-24-banging.html

Point taken but an appliance specific question is not the same as one on a generic subject that had been 'done to death' a few weeks ago.
Besides, if the filling loop is bought in a plumbing shop then the staff there or another customer should be able to answer the question of orientation in a few moments.

 

[buckley plumb]

I'm guilty of fitting them on the heating in the past mainly because the cheaper ones came without an iso and ignorance to be honest! I assumed the check valve had to go onto the heating side because of the directional arrow of flow printed on them. They must go as Chris has said ... On the cold water main

aggree the cheap ones can only be fitted that way been using the pts ones they have 2 valves