Search the forum,

Discuss Veissmann vitodens 222F combi boiler Help in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
O

Ole Fella

Greetings guys
i was hoping you might help an old fella out with what ill seem rather simple issue for you tech savey guys in regards to the programming of my veissmann combi boiler.

we have Installed as mentioned above the veissmann vitodens 222F combi gas boiler with the vitotronic 200 control unit. we have been using only the central heating side of the unit to heat our house as we have had individual electric water heating for our potable water ( bathrooms/ kitchen)

we have recently renovated a new bathroom and made a plumbing connection to the boiler but im unable to get the hot water working .... i can either have the house warm or have a nice hot shower i cant seem to get both.

i beleive this unit only has a single internal pump what has to be used by both the rads and the DHW but only one at a time. so my thinking is that it has to do with the timing programs of the DHW.

ive got the Rad room temp set at 22 and timer set to 6.00 to 22.00 ( this works great with no problems )
when i go into the DHW settings and raise the temp to 50C ( the recommended temp) i can hear the hot water being created and fill up the ho****er storage tank (i assume) and i can have a hot shower but in doing this it turns of the Radiators and they never turn back on again untill i drop the DHW temp back down to 30 than i hear the burner turn back on and how water return back to the radiators.

im sure it has to do with the program times.


for those familiar with this boiler and the vitotronic 200... this is what im trying to acheive ...

rads on between 6.00am -10pm
DHW on between 7-9am and 4-8pm
and also hot water on demand at all times ( as i understand this is water that is created outside of these preset times that is instantly created

not sure if this is poossible but logic would say that it is but im just unable to figure it out.

any help would be greatly appreaceated and it will make that wife happy :blush5:
 
A combi boiler is both a high-efficiency water heater and a central heating boiler, combined (hence the name) within one compact unit.

A combi boiler will alway give priority to hot water. The combi will do the hot water or the heating. Combis don't have the capability to run both heating and hot water parallel with each other.
 
A combi boiler is both a high-efficiency water heater and a central heating boiler, combined (hence the name) within one compact unit.

A combi boiler will alway give priority to hot water. The combi will do the hot water or the heating. Combis don't have the capability to run both heating and hot water parallel with each other.
 
A combi boiler is both a high-efficiency water heater and a central heating boiler, combined (hence the name) within one compact unit.

A combi boiler will alway give priority to hot water. The combi will do the hot water or the heating. Combis don't have the capability to run both heating and hot water parallel with each other.

cheers amgas ....ya i was thinking that this was the case still i need to know how the time setting programming works ... do i set the DHW to run only during a coupld hours a day say early in the moprning and in the evening to make sure there is hot water in the hot water tank (100l) ready to go fr showers ... and have the Central heating left at 6.00 -2200

and say we have lots of guests over and 100L insnt enough will it creat instand hot water as we need it ? and what tempratuire should we set the DHW at i was told 50C is the accurate

cheers
 
Status
Not open for further replies.

Reply to Veissmann vitodens 222F combi boiler Help in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello, I am seeking some advice, I have a POTTERTON PROMAX 28 COMBI Boiler and I noticed yesterday that the water around the house is no longer warming up. The heat exchanger has been changed 6 months ago, so I do not believe it is that. Does anyone have any ideas on what it could be? Thanks
Replies
4
Views
275
  • Question
Ideal Logic 24, Previous problem was that the hot water was only cold or barely warm if the heating was in use. If heating was off and boiler cold then would get hot water most of the time. Changing the flow cartridge about 2 years ago (when I moved in) solved this problem enough to suffer it as...
Replies
2
Views
174
Every two weeks or so I have to go and top up the system because the hot taps are running cold. Boiler display is flashing 0.6 bar and I fill up to 1.3. I've had an engineer look inside the boiler and he can't see anything wrong. I've checked the pipes all over the house and cannot see any...
Replies
2
Views
247
PSxxxxxx
P
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
350
We run a community village hall and have a large kitchen provided for the use of hirers. This includes a Lincat SLR9 gas cooker which I believe is a 23.8Kw appliance with all six burners and oven on max. This was installed some 10 years ago and has passed all subsequent Gas Safety inspections as...
Replies
5
Views
522
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock