Search the forum,

replacing

In computing, replace is a command that is used to replace one or more existing computer files or add new files to a target directory. Files with a hidden or system attribute set cannot be replaced using replace. The command lists all files that are replaced.

View More On Wikipedia.org
Recent contents Top users
  1. K

    Replacing diverter valve

    Hi, this is my first post.. hoping it's an easy one that someone can help me with. I've got a standard system (not a Combi.. just a Bosch gas boiler and a hot water tank). Anyway.. everytime the CH valve turns off, I get a REALLY LOUD clunking noise from the system. I've done some reading...
  2. M

    Replacing taps behind the washing machine??

    Hi i am new & useless at DIY i have old bulky plastic taps connected to my washing machine - due to new units being fit i need 3 cm more space at the back so can i replace with smaller taps? also as the washer is 10yrs old can i cap one off ..if so which one,, hot or cold? i appreciate your time...
    • Mick HX
    • Thread
    • america behind machine replacing taps usa washing washing machine
    • Replies: 9
    • Forum: USA
  3. J

    Approx price for replacing tempering valve on solar hotwater

    Just wanting advice on the average cost of installing a tempering valve on a solar hot water system located on the roof of single storey home. Ive been charged $445 inc gst, no extra parts needed and took plumber less than 30 minutes to install, it seems a bit steep Any advice appreciated
    • Jaymuss
    • Thread
    • america approx australia hotwater price replacing solar usa valve
    • Replies: 10
    • Forum: USA
  4. D

    Replacing British Gas 330+ System Boiler but keep flue

    Hi In new flat, looking to replace BG 330+ system boiler with a combi, but retain existing flue as there are a few bends and quite long - it's still in good condition #(8 yrs old). I'm told the boiler was made by Glowworm, and that their new Energy 7 would do the trick. I'm thinking of buying...
  5. E

    Is a central heating system flush needed after replacing a radiator?

    I purchased a Kudox steel panel radiator to replace a radiator that developed a leak. There is a warning triangle on first page of the Installation Instructions with the following in red capital letters: ‘AFTER INSTALLATION THE ENTIRE CENTRAL HEATING SYSTEM MUST BE THOROUGHLY FLUSHED WITH A...
    • Enthalpy
    • Thread
    • after central central heating flush heating heating system needed radiator replacing system
    • Replies: 3
    • Forum: Central Heating Forum
  6. C

    Replacing an old radiator with a fancy new vertical one

    Hope you can give me some advice. We have an old radiator in our living room which we'd like to replace with a nice vertical one. We're looking at the 1780 x 472mm Anthracite Double Oval Tube Vertical from Radiator Outlet. I have no idea how feasible this will be. The supply pipes are 10mm ones...
  7. U

    Replacing a humidistat with a thermostat

    Hi folks, With gas prices going through the roof I've been looking to maximise the efficiency of our heating. We've got a Potterton combi boiler which is regularly serviced and has generally worked well for the 4 years we've been here. What has always confused me is the 'thermostat', which is...
    • UniversallyChallenged
    • Thread
    • america central heating system replacing thermostat usa
    • Replies: 11
    • Forum: USA
  8. NeetieM

    Replacing a 12 year old air source heat pump

    Hello, I hope someone can give me some advice on replacing an old air source heat pump. We moved into a shared ownership house last year which has a Daiken air source heat pump fitted to provide heating and hot water. The unit was fitted when the house was built 12 years ago. It seems that the...
    • NeetieM
    • Thread
    • air heat heat pump old pump replacing source year
    • Replies: 6
    • Forum: Renewables
  9. D

    Replacing Drayton SM1 with LP711

    Hello I'm new here so I hope this is in the correct section. I'm looking to replace my very old Drayton SM1 mech timer with a Drayton LP711. Would anyone know is the back plate wiring exactly the same is it a straight swap or do I need to change anything.?? Thanks.
    • Donhel
    • Thread
    • america drayton replacing usa
    • Replies: 2
    • Forum: USA
  10. E

    Replacing P trap under kitchen sink

    Hi there, My under kitchen sink p trap is slightly leaking, I've tightened the nut and still a leak there. Looking to buy a replacement and the code on the pipe just now is McAlpine EN 274 3. Anyone know where I would get a replacement and I've seen various sizes? Thanks 😊
  11. A

    Leak since replacing aerator

    I have a pedestal sink. The female aerator was clogged. I bought another one. Screwed it in tight and immediately it started leaking behind the sink. I took it off and ran the water without the aerator and it did not leak. The new aerator is the same diameter but just slightly shorter. Is it the...
    • Apriljh5
    • Thread
    • aerator america leak replacing since usa
    • Replies: 1
    • Forum: USA
  12. P

    Replacing entire filling loop on Vaillant EcoTec Pro 28

    Hi all, I think has been discussed before but I don't think I've seen a clear answer. We have the Vaillant boiler as above and the filling loop has started to leak from around the olive joint on the cold water side. I would like to replace the whole loop, flexi, taps and the valves etc. I can...
  13. D

    Replacing gas hob with existing cooker hood inside hot zone

    Hi, my gas hob needs replacing but I'm told first the existing cooker hood must be raised as it's 70cm instead of 75cm above gas hob as per new regulations. Is that right?
    • dasau29
    • Thread
    • cooker existing forum gas gas hob hob hot inside plumbing replacing zone
    • Replies: 2
    • Forum: Plumbing Zone
  14. S

    Replacing Kitchen Tap - what is the minimum insertion depth for push fittings?

    Evening all, Basically my question is how deep must a 15mm copper pipe be inserted into a push fitting for it to function properly without leaking? I Bought this Tap Tail Adapters from Toolstation this morning and I am wondering if they are deep enough. I tried to install a new mixer tap this...
    • ScottishRabbit17
    • Thread
    • america depth fittings kitchen minimum replacing tap usa
    • Replies: 5
    • Forum: USA
  15. D

    Replacing radiator with towel rail - help needed

    Morning all. Wondering if you can help. I'm re-doing my bathroom and thought I'd replace the radiator with a towel rail. The plastic pipes seem to be speedfit (or similar). I can't see a brand on them and they say 15mm (but they're clearly 10mm). The current pipes won't stretch to the new...
    • DIYnovice1
    • Thread
    • america help help needed needed radiator rail replacing towel towel rail usa
    • Replies: 15
    • Forum: USA
  16. S

    Replacing DT10RF Optimising Programmer that's faulty

    Hi My 8 year old DT10RF's screen is failing and becoming difficult to read. My 8 year old boiler is a Worcester Bosch Greenstar 34CDi Classic. I have been thinking of replacing with a wifi controller that I can use over the internet and smart radiator thermostats (Smart TRVs). Is this...
  17. S

    Replacing Toilet flush valve

    Hi I'm trying to replace a bottom entry toilet flush valve - but having problems with tight access and in particular having problems loosening the bolt to get rid of the plastic that remains of the existing valve - see photo attached. I don't seem to have enough room to get spanner or wrenches...
  18. M

    Replacing pop up plug and waste in bath. No screw to remove drain cover from plug hole.

    Hi, the pop up plug system has broken and needs replacing. I would like to replace the whole lot. My issue is trying to remove the waste drain cover from the bath isn't what I'm expecting. There is no screw holding the trap to the plug section in the bath. As the bath is fiberglass, I don't want...
  19. S

    What are my options replacing toilet with waste pipe in floor?

    A few years ago I had to replace my old, 1960's downstairs loo as it had a crack in it. I was told that, because the waste pipe went down into a hole in the concrete floor and because of the distance of that hole from the back wall (20cm), I'd need a loo with a concealed cistern in a large...
  20. B

    Replacing Shower Diverter Valve / 15mm to 1/2" BSP fittings

    Afternoon, all. Currently have proprietary diverter valve on shower riser with handheld outlet standard 1/2" BSP male and inlet also 1/2" BSP male. The outlet to overhead shower is custom female fitting and feeds a larger diameter chrome covered plastic pipe feeding large and inefficient...
    • BogginsDad
    • Thread
    • 1/2" bsp 15mm america bsp diverter diverter valve fittings replacing shower usa valve
    • Replies: 7
    • Forum: USA
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Tiling Advice
Tilers Forums UK
Tile Talk
Tilezine Tiling News Tile Association
TilersForums.co.uk
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock