I'm looking for some advice on installing a toilet in an outbuilding before I get some prices in from plumbers!
I'm having an outbuilding built in my garden and would like a toilet and kitchenette in there but the problem I have is the building is about 20m away from the back of the house where...
I'm an end user with limited knowledge of plumbing and just trying to get an understanding of options available to me. We currently have a Valiant Combi Boiler Sealed Unvented Heating system. It was installed 3 years ago and works perfectly well for both CH & HW. Recently we built an...
Hi, I'm installing a new mixer tap in my kitchen. The current setup doesn't have any isolation valves so was thinking I'd cut the pipe, install a couple of flat faced isolation valves and then screw the flexi's into that. My question is, should I be using PTFE on the threads, joining compound on...
I am trying to install Sellkirk flexible vent onto my water heater and I’m getting confused as to which end connects to the water heater and which end attaches to the existing vent pipe. The flexible pipe has two ends one of which is a male one of which is female but I don’t know which is which...
Hi everyone, I want to fit a tall rad in my bathroom which will be fed from above, but I would like to keep the pipework to a minimum. Is it necessary to run both pipes to the bottom of the rad, flow to the bottom and return to the top, or will it work with both to the top? I'm not sure as yet...
Hi all
I just had a conversation with a heating engineer and he did not want to install my requested boiler (Worcester 50kw combi boiler) saying he would only install a 25kw or 30kw boiler
The reason I would like a 50kw boiler is the flow rate 20 l/min. He recommend a pressure relief value but...
We are currently looking at the possibility of purchasing a new build terraced property. The outside tap is located at the back of the property.
How easy would it be to install a outside tap at the front of the property? Ideally it would need to have its own valve inside so knowbody else could...
Hi there!
Recently moved in to a new property in Sweden, previously heated with fires and electric rads. Have contracted someone to install a Ground Source Heat Pump, but will undertake the installation of rads myself. The property is around 120sqm over two floors, and I will be setting in 11...
My central heating controller (Horstmann H27XL) is getting more difficult to use due to it's age and because of a disability I have reduced dexterity in my fingers and find the buttons difficult to press. I have been looking at these so called smart thermostats such as Nest, Hive and the...
I am planning to refurbish a bathroom in a "modern" house - ie 30 years old. Part of the work is to install a new shower pan and cubicle together with wall boards (inside the shower only). The bathroom is upstairs and sits on a chipboard floor. Although there is no evidence of leakage under the...
good evening
what fixings do people use to fix shower enclosures through tiles into plasterboard? ive seen the grip it style but i don't know how you could use that through a tile?
thank you for reading
The internal coil is corroded (leaking) Its an indirect storage cylinder so there's no health problems...But changing
the cylinger is complicated. I'm looking for a flanged retrofit spiral coil with flange. Any suggestions? Thanks Justin
Hey guys
My house has a ensuite with a broken SANIPLUS macerator which has been out of use for the past 5 years. Stupid I know, my parents haven't bothered to fix it lol
Question is how much should I be looking at for installing a new one if I were to pay a plumber ? and secondly do you guys...
Just purchased a Mira Platinum shower (dual ceiling fed high pressure/combi boiler version), which will be installed in the loft directly above the shower area in a bathroom that I am refurbishing.
I've read through the installation manual and a couple of things aren't too clear:
1. A couple...
Hi guys. What's the preferred method of installing hot and colds to a basin on a ped? I know a lot are piped up inside of the ped but with monabloc mixer taps on flexis I'm thinking it may result in the pipes knocking about? Any advice you guys have would be great, thanks.
I have an open vent CH system with two cold water tanks in the attic.
The hot water cylinder from the first-floor feeds the hot water to the bathroom (currently no shower is fitted in the bathroom) and a shower in en-suite all on the first floor.
The hot feed from the hot water cylinder to the...
just bought a bungalow which as 11 rads which i plan to replace and reinstall them with plastic pipe in the brick walls etc the property is 19 meters long and 7 meters wide the boiler is situated in the middle of the property and the boiler is a greenstar 28i junior 2014 model. question is i...
Please let me know how to replace the seals in a Barber Wilsons kitchen "gooseneck" faucet. These are the seals that go in the base of the gooseneck, not the individual faucets. I have the kit from BW - four rubber seals/washers, two metal "half" washers and an aerator. If you have photos of the...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.