Trying to solve a little mystery to do with minor leaks from manifold valves. Attached image shows the valve (new) and the arrow shows the point of leakage. It seems the internal seal of the moving pin has deteriorated over time. May I add that the valve is not stuck, its moving freely.
Its a...
Hi all
I have underfloor heating downstairs and radiators, plus two towel radiators upstairs. I have a Heatmiser UH8 and the radiators are connected to the the 5th zone and the towel radiators are connected to the 8th . Now, if I remember rightly from manuals, if you want to hook up a towel...
Hi - got an aqualec UFH system with aqualec thermostats in each room displaying the temp, with a ESI programmer in the utility room in my flat.
The plumbers have just recently changed the install so that when the heating programmer is off, the thermostats go off and don't display the...
Evening all, I’m looking to do a make over to our future home, I was thinking of UFH downstairs and rads upstairs. Then stumbled across skirting board heating, I realise it’s not a new thing in the world, but is to me, I’ve never fitted it or had experience with it. I wondered if you gents or...
Hi,
Thanks for having me. I own a B&B in the far NW of Scotland in the village of Durness on the NC500 route.
I have an Encompass underfloor heating system connected to a Grant oil burner and associated with a Santon Premier Plus unvented hot water system. I keep losing pressure in the hot...
Hi Guys hope you can help, I have a wet underfloor heating system and have 6 zones, the problem I'm having is one of the zones is getting warm even though the master thermostat/controller is turned off, the pump is not being switched on so is not circulating through the system. I have an 'Ideal...
Hi
I have an installation for CH half way installed (first fixed)
I want to tile all the floors.. and have realised it will be too cold so I thought about laying pipes in the floors instead of having radiators and simply using the flows and returns that are already there for the radiators to...
Deleted member 102951
Thread
heating
pipes
ufh
under floor heating
underfloor
underfloor heating
Hi all,
New to this forum but hoping you could give me a hand with some issues I'm having with my UFH.
I bought a house in Nov last year that has wet UFH in a kitchen extension. It's a relatively small area with only 2 loops, total 90m piping and 2-port manifold. Manifold model is Wunda...
Hey guys
Where is the best place to have my manifold? I want 3 zones.
The kitchen is 2.4 x 3.1 m
The bathroom is 3.1 x 3.1 m (Directly above the kitchen)
The conservatory is 2.1 x 3.1m (Directly next to the kitchen boiler wall)
The kitchen is the natural choice as all 3 zones are nearby, and...
Hi
I have a polypipe multizone underfloor heating system (Gas) that stopped working a few weeks ago.
It had been making some screeching noises and my hunch in that the Grundfos pump has died as the screeching has stopped - along with the heating! I may be wrong of course.
The LED's on the side...
I’m an electrician, a plumber has asked me to look at wiring in a care home for UFH with a system boiler.
Only way to get it to work is run everything constantly.
The wiring center was a mess, i’ve rewired and now working as expected.
However, it appears to me there is an unnecessary valve...
Hi all,
Just looking for some help. Moved into a house last year that already had UFH installed, but I have no information about the system and one of the air flow caps has spring a leak.
Managed to cap it for now but trying to find a replacement part.
The manifold has nothing written on it...
Hi all!
Sorry if this has been asked before but i haven't been able to find anything out there...
We made our CH system zoned when I laid some UFH in the kitchen. (2 zones total: kitchen + rest of house) each zone has a Honeywell 2-port zone valve. The boiler is a Glowworm combi.
All is well...
Hi guys
Our recently installed UFH system is causing us trouble and we are struggling to get the fitter to help, problem one is we have to slowly build up the heat as the new floor is tiled but the only way to do this is by turning the boiler heating controls down as low as it goes, 30 degrees...
Hi all
Newbie here who has joined to try and learn from your collective wealth of experience! I am a homeowner and not in the trade. You will see this from my lack of technical terms, Trying to do as much research as possible so we get it right - this is a one time opportunity and we need to...
Hi All,
I have failed in my journey and I now need some advice. I have been trawling this site and the Internet for over 1.5 years to find the answer to my problem. I have reached out to three plumbers and the fitting company of the system but unable to get anyone through the door. I am a...
Hey guys
Ive carried out some rough calculations as to how much of my concrete floor I'll have to break out to fit a UFH system and I'm concerned about the amount of work involved and the number of skips I'll need and was wondering if I can reduce the amount of digging I need to do.
I was...
Hi,
Following a full refurbishment of an house and a new build rear extension we had a brand new heating system installed. Give you an idea of what it is:
Vaillant 637 system boiler
300l Water tank
Wet UFH (floor area 15x4m) in new rear extension (family area, kitchen and dining) - used all...
Afternoon Lads and Lasses. I am setting up a 2 circuit UFH system the manifold has 3 ports. Do I blank off the spare ports or do I fit a loop and leave it turned off ? The other ports will be controlled with room stats.
Hi guys, probably a silly question but in my new extension I have water UFH connected to my combi which runs the radiators in the rest of the house.
Although both are controlled separately do they use the same water? What I mean by this is if I put inhibitors in a radiator will it also enter the...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.