You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
push fit
A push-up (sometimes called a press-up in British English) is a common calisthenics exercise beginning from the prone position. By raising and lowering the body using the arms, push-ups exercise the pectoral muscles, triceps, and anterior deltoids, with ancillary benefits to the rest of the deltoids, serratus anterior, coracobrachialis and the midsection as a whole. Push-ups are a basic exercise used in civilian athletic training or physical education and commonly in military physical training. They are also a common form of punishment used in the military, school sport, and some martial arts disciplines.
I have added a new radiator and pipework but unfortunately I have a joist that is directly below where I need a 15mm elbow to connect up to the radiator. I have used plastic speedfit piping and fittings throughout which means if I notch out the joist the notch would be too big as the plastic...
Been ripping out a few jobs where the surface pipework is ran in chrome compression. Although in the walls it's all poly and they have even come straight out of poly plumb elbows with the chrome pipe. I have always been so against that and even though it's not highly recommended I have always...
Hey when say piping up a kitchen sink were the pipes are elbowed out behind the unit via a push fit elbow taking the plastic pipe to copper coming in to the unit. You would usualy want to elbow the pipe straight up to go to the kitchen tap. However his wold mean soldering ly a few inches from...
The wife has asked me to replace the kitchen mixer tap. We have a new flexi hose type replacement. However, having just popped my head under the sink, it doesn't look compatible The current tap has solid pipe running to what I am presuming to be push fit connectors. Where I expected to see a...
Was asked to look at a leak at at newly fitted bathroom. The leak fixed so no bother on that. But one thing that flagged my attention was that a copper push fit elbow that goes up to the electric shower has corroded quite badly, see picture below. Its only been in for a few months. Any idea what...
Had a discussion tonight down the pub about push fit brands and mixing I said I'm pretty sure your allowed to mix say hep2o fittings with poly plumb pipe...
Hi,
I was wondering where to get a 157.5 degree waste push fit elbow from as my existing one is damaged? It is 32mm and made by Osma but I can't seem to find it anywhere, I can only find the 45 and 90 degree ones.
Thanks.
Nas7001
Thread
degree
elbow
order
polypipe
probably
product
pushfit
Hi all,
Any idea on how I can join solvent weld 32mm pipe to push fit pipe? I have tried a compression elbow but it is too lose in the push fit pipe.
Thanks
We tend not to use any push fit but has anyone got any experience with push fit going wrong?
For example
Push fit stop end popping off, who would the liability be with? Us or manufacturer - this hasn't happened but just wondering if we used plastic stop ends to temp isolate copper for a...
I know that push fit plastic pipes arent allowed within a meter of the boiler, but i can remember where I read it, is it a gas safe rule, doc L, manufacturers instructions
I need to quote the exact rule, came accross a boiler which had recently been installed while doing a CP12 friday...
Hi, new to this forum. I have a leak from a plastic push fit elbow. It is grey and marked HBP 15, my research so far says this is an old style hepworth fitting? It doesn't appear to be easily dismountable, but is there an easy way. It is on my central heating system connecting the main pipe to a...
Which is the best push fit for continuous use (for testing) Has anyone found a pushfit thats good for testing use, there's nothing worse when testing all ok then you cannot remove the bloody thing, i have to cut several off and get them off in a vice.
Cheers
steveafoss
Thread
after
prefer
pushfit
remove
speedfit
testing
whats
Would you / Could you ... use copper push fit connectors under flooring or within wall cavities?
How likely are they to fail compared to solder connections?
Regards
DIYBlues
Hi all.
Quick question.
Pushfit/speedfit on an unvented. I believe the reg's are that it's not allowed within 1 metre of cylinder?
Is this true?
I have fitted thermal stores where the manufacturer actually tells you not to solder directly to the store, or use compression, but use a pushfit...
i have a couple of little jobs..........(moving 2 rads and fitting new outside tap)
a lot of people say push fit is the way to go. i dont mind having a go at soldering and have aquired the tools to do it.
if i paid a half decent plumber to do the jobs what should i expect to see them using...
What is the minimum distance a copper push fit fitting can be from a condensing boiler on the cold water inlet pipe, I have been told its 600mm but cannot find this anywhere
Steve
hi all. im in the middle of doing the plumbing for my bathroom and i wanted to use some push fit fittings to the taps. the basin tap is a monoblock mixer tap 15mm x mx10 i also need some pushfitings for the bath tap which is 22mm so ill need 15mm to 3/4 inch with service valve. any idea where i...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.