You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
mixer shower
A vortex mixer, or vortexer, is a simple device used commonly in laboratories to mix small vials of liquid. It consists of an electric motor with the drive shaft oriented vertically and attached to a cupped rubber piece mounted slightly off-center. As the motor runs the rubber piece oscillates rapidly in a circular motion. When a test tube or other appropriate container is pressed into the rubber cup (or touched to its edge) the motion is transmitted to the liquid inside and a vortex is created. Most vortex mixers are designed with 2 or 4-plate formats, have variable speed settings ranging from 100 to 3,200 rpm, and can be set to run continuously, or to run only when downward pressure is applied to the rubber piece.
Hi all.Could I feed an en suite mixer shower from a loft cold tank through an inline instant electric heater and twin impeller pump.If so would the pump go before the heater or after.I would appreciate any other idea's if mine is not feasible.
In the middle of a total refurb and having some weird bathroom plumbing issues.
Context: it's a new combi boiler, new mixer shower and bath tap. No other taps currently plumbed in.
The shower only kicks the boiler on in the evening, not in the morning.
In the morning I can get hot water for a...
Hi all,
I hope you are well.
We bought our first property in the middle of last year and as such, this has been my one of my first experiences of having to do anything remotely DIY related (we have previously lived in rented properties where the landlord sorted out the DIY, via their...
hiya fellas ,
Been given a bathroom spec and it includes a universal single impelled pump to run a ( hot side)mixer shower valve... and been toto connect cold side into mains...? Is that asking for problems.. i.e. Unbalanced supplies
Im trying to service the Cartridge on my Bristan Rio Mixer, and I’m stuck! The instructions from Bristan don’t make sense when compared to the unit.
I’ve taken off the tap head part from the thermostat control. I can’t find any grub screw under any where to expose the Cartridge. Might it be...
hi all, does anyone know who makes this mixer it has aspirante written on it. I have fifty flats to work in that all have this model.
Any ideas?
Thanks
Hi there,
Looking to install a thermostatic mixer shower in a flat with night rate unvented cylinder. It's an almost like-for like replacement for a thermostatic bath fill/shower diverter which has a broken thermostatic cartridge.
During the day, hot water temperatures can fall to 45°C, or...
Hi all
I need some help, I'm really hoping you guys can give me some advice!
I'm a 2nd year plumbing apprentice so feel stupid having to ask, but because this is so important I'm worrying I may make mistakes and I need to get this right!
My Dad has End stage cancer and is at home. My...
I have a Bristan mixer shower that keeps going cold, it goes cold for a minute or so and then comes back hot before going cold again. I have replaced the cartridge in the shower and also replaced the shower hose, there was a slight improvement for a week or so but it is now back to what it was...
Hi
I need to replace a thermostatic mixer shower, but the surface water pipes are only 3.5 cm apart - I believe they are mainly 150 mm apart nowadays?
I would like to do this with minimal disruption - does anyone know if anyone manufactures a shower with such a clearance? If not, what would...
I have a combi boiler (Vailant ecoplus) and a mixer bar shower. The taps in the rest of the house, including bathroom, get super hot on demand. The pipe behind the mixer shower are very hot to the touch and yet even woth the thermo valve on the mixer at full it is moderately hot at best.
Ive...
HarryHarris
Thread
fitted
mixermixershower
pressure
shower
temp
valve
water
Hi,
I have taken apart and bought a new (really expensive) cartridge. I found a broken up contact in the shape of the attached comedy sketch. Does this go on the contact of the cartridge and between the spring. Anyone know of where I can buy this spare? Thanks.
Rich
Hi guys I have a mixer shower at home and it's made by Mira, sometimes I turn it on and it's fine get a good shower out of it then I get out and other half will go to use it, and it just won't turn on just wondering if a fault like this is quite common and what I can do to fix this .?
Thanks Tom
Hi,
I need to replace a shower mixer valve on an unvented system, and as it's concealed there are no isolated valves. Is there anything specific I have to do to system to isolate h/w or is it just like a standard g/fed system and shut cold off and h/w feed on cylinder?
Cheers
Hello,
I really hope somebody can help me with this problem.
We have an Exposed Thermostatic Mixer shower, with 22mm inlet/outlet pipes, that needs replacing.
We can only find similar mixer showers made for 15mm pipes, and have been told that this is now the standard fitting. This is a real...
James McC
Thread
22mm
cold
exposed
heating
hot
mixermixershowershower
thermostat
thermostatic
Hello,
Please could someone give me some advise.
We have a combi boiler but for some reason the previous occupants left the cold water tape in the loft.
We changed the shower to a mixer shower and ever since the shower bangs when being used. The tap are fine but the shower really bangs.
The...
Hi all, I was hoping to get some advice re a problem I'm having with a mixer shower. Recently had a new boiler fitted. We have a bar type mixer shower, problem is it won't stay hot. It will start hot then after a few minutes it will go cold. The boiler fires up when you start the shower, stays...
Cobby
Thread
boiler
cold
hot
minutes
mixermixershower
rates
shower
I have a Gainsborough thermostatic shower mixer valve. The water coming out of it isn't as hot as it was, not really hot enough for a shower. Strangely, the hot pipe in the cupboard behind valve that feeds water to shower valve is very hot. When I run the bath cold tap (the bath has it's own...
Hi, I need to replace a bar mixer shower for a customer, the existing shower is bristan and has fixed 130mm centers, spoke to bristan and they no longer make one with 130mm centers, they have showers which are "adjustable from 130 - 170 but this is via the z connectors at the back which it seems...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.