Search the forum,

mixer shower

A vortex mixer, or vortexer, is a simple device used commonly in laboratories to mix small vials of liquid. It consists of an electric motor with the drive shaft oriented vertically and attached to a cupped rubber piece mounted slightly off-center. As the motor runs the rubber piece oscillates rapidly in a circular motion. When a test tube or other appropriate container is pressed into the rubber cup (or touched to its edge) the motion is transmitted to the liquid inside and a vortex is created. Most vortex mixers are designed with 2 or 4-plate formats, have variable speed settings ranging from 100 to 3,200 rpm, and can be set to run continuously, or to run only when downward pressure is applied to the rubber piece.

View More On Wikipedia.org
  1. C

    help with a mixer shower problem

    Ok when i bought my house almost 3 years ago i fitted a thermostatic mixer shower however i always had a problem where if i had the temp at say mid all preasure dropped you had to have the temp on the shower up full and then have to turn down the tep on my combi boiler to have presure and...
  2. K

    mixer shower question

    hi my father in law has passed on an unwanted rada thermoscopic 215-t3 temperature control. it's a big thing with 3 inlets coming off it i believe 1 hot 1 cold and 1 wate, trouble is its only a temperature control theres nothing to actually power it. ive bought an exposed shower kit to go with...
  3. B

    combi boiler to power mixer shower?

    hi.how is the best way to tap into a combi boiler to power a mixer shower :confused:
  4. W

    mixer shower cw prob

    fitted ensuite couple months back, had call from customer telling me no c/w coming from mixer shower occasionaly, only hot (concealed mixer). investigated to find c/w will run but not everytime shower turned on. turned mixer to cold, turned on shower, no c/w. went into bathroom and turned on...
  5. F

    plumbing a thermostatic mixer shower

    Hi, I need to plumb in a thermostatic mixer shower over a bath. there is no exsisting shower only mixer bath taps. do I need to plumb in separate pipe from the hot water tank or can I cut into the hot and cold supplies for the bath taps? Also any one have any advise on sinking a bath into...
  6. G

    Mixer shower problems - Help!

    Hey was wondering if someone could please help me with my mixer shower problem? I know jack about plumbing and desperately need help as I am sick of baths. Ok, here's the problem. I got a guy out to quote me on getting my bathroom re-done and also a combi boiler installed. I asked him to go...
  7. J

    what's this for..... mixer shower flow issue

    Hello, Can anyone advise? No cold coming to my shower (since combi install). Have adjusted everything I can see/reach/adjust but nothing working. The thermostatic mixer has these two screws on each water feed (see picture). Can anyone tell me what they adjust? The one I can turn seems to...
  8. N

    Mixer Shower

    Ok, very poor pressure on shower, wc and basin taps in ensuite (Both H & C). Took up boards to look at pipes. Found:- 1 x 22mm Dia feeding HOT shower outlet and HOT tap 1 x 15mm Dia feeding COLD tap and WC Cistern 1 x 15mm Dia feeding COLD shower. Is this the way it should be acc to Regs? I...
  9. K

    Help installing mixer shower

    Hi, I'm about to install a Triton Altair bar mixer to a RD628 combi system. The mixer h/book states a PRV must be fitted if the mains pressure is above 5 bar which it is. And this is fitted on the mains inlet to the combi, would this upset the boiler setup ? or would fitting it to the mixer...
  10. B

    What Mixer Shower

    I have just moved into a house which has a Worscester Combi 24CDI Boiler. I want to install a separate Bath Shower complete with a Thermostatic Mixing Valve ( Possibly a Mira Excel ). I have taken the following test results from the "Combi Boiler supplied" existing hot water bath tap:- Flow=...
  11. C

    mixer shower fitting.....

    Can i use grey plastic pipes inc push fit adapters from the cold water cistern in the loft and the cylinder to fit a mixer shower into the bathroom??? And the grey plastic pipe... does it have to be 22mm dia from the cylinder to the mixer shower?? Cheers.........
  12. C

    fitting a thermostatic mixer shower......

    I need to fit a thermostatic mixer shower in the bathroom, can i come off the hot and cold pipes leading to the bath and sink....?? Any advise :confused: Cheers.....
  13. O

    imperial thermostatic mixer shower?

    does anyone know if any of the imperial mixer showers can have the thermostat adjusted for better temperature? this one is about 6 months old runs off a pump, pump is fine but shower runs luke warm and wont get hot/ wont stay hot. have cleaned the thermostat but not made any difference. any...
  14. T

    mixer shower help

    hi all this is my first post I got called out the other night to sort a overflowing cold water storage tank after inspection the ball float valve is fine not passing, after a short while the lady of the house informs me, that it happens when they get a shower. After inspecting shower i find the...
  15. P

    Triton mixer shower

    I have just been out to look at a 10 year old Triton mixer shower,the problem is it allows very little hot water through it causing a cold shower. I have taken the cover off and exposed all the screw heads to get into it and have the instructions with exploded diagram. Can the cartridge...
  16. J

    Help with manual mixer shower prob

    Hi chaps, Would appreciate some help. I've installed a manual mixer shower on a open vented system, only to find out later that the shower doesn't work properly. You will already know that this is because the cold feed upstairs is linked to the rising main and the hot is fed from the loft...
  17. J

    Unbalanced water for mixer shower

    Hi, Does anyone know if using a pressure reducing valve for an unbalanced system will work. It's for a mixer shower that has been fitted. It's a gravity fed system so the hot comes from the water cyclinder but the problem is - the cold is connected directly to the rising main. This prevents...
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock