You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
thermal store
Thermal energy storage (TES) is achieved with widely different technologies. Depending on the specific technology, it allows excess thermal energy to be stored and used hours, days, months later, at scales ranging from the individual process, building, multiuser-building, district, town, or region. Usage examples are the balancing of energy demand between daytime and nighttime, storing summer heat for winter heating, or winter cold for summer air conditioning (Seasonal thermal energy storage). Storage media include water or ice-slush tanks, masses of native earth or bedrock accessed with heat exchangers by means of boreholes, deep aquifers contained between impermeable strata; shallow, lined pits filled with gravel and water and insulated at the top, as well as eutectic solutions and phase-change materials.Other sources of thermal energy for storage include heat or cold produced with heat pumps from off-peak, lower cost electric power, a practice called peak shaving; heat from combined heat and power (CHP) power plants; heat produced by renewable electrical energy that exceeds grid demand and waste heat from industrial processes. Heat storage, both seasonal and short term, is considered an important means for cheaply balancing high shares of variable renewable electricity production and integration of electricity and heating sectors in energy systems almost or completely fed by renewable energy.
I have an Albion indirect mainsflow thermal store installed in July 2011 with a 120 litre capacity.
I live in a block of communal council flats built in 1979. I have gravity fed water tanks on the roof of the property about 3-4 stories high. Pressure to my property on the cold water supply is...
Can anyone tell me the hot water flow rate on a thermal store combi boiler? As opposed. To a 40kw combi that will deliver nearly 16litres per minute. And any recommendations for a good thermal store boiler thanks.
Hi there, we replaced our Rotex Sanicube thermal store after discovering large amounts of sediment in our hot water supply. It was replaced with a Wocester Bosch unvented 250l cylinder.
The sediment issue was resolved immediately but have noticed a large increase in oil usage. Probably going...
Sorry for a long post but we have a complicated thermal store situation
Over the summer we had a new solid fuel stovax back boiler installed and upgraded our hot water storage tank to a thermal store.
We have not had reliable hot water since. Initially we only used the emersion and after...
I am looking to install a thermal store to replace my current vented cylinder. I plan to use an external plate exchanger for DHW and heat the store directly from my existing vented boiler. So what I am looking for is a plain stainless steel tank (no internal coils) with a variety of connections...
I am moving house and looking to install a thermal store in the new place. I was thinking of an unvented store around 300l, with a single corrugated stainless coil for DHW.
Any suggestions on make/model/supplier?
Hello...
Looking for advice regarding a replacement for my old Range Flowmax 140 Thermal Store combination cylinder that is starting to show its age.
I wondered if anyone had any recomendation for which manufacturers to look at? I know they are not cheap anyway, but I dont mind spend a bit extra...
Sorry if this seems a trivia question , but just watched a programme called the chateaux with dick strawbridge .
My question is regarding the fact that he put a thermal store right at the top of the building 4 floors when the boiler was in the basement , what is the logic in this as I thought...
Now sorted... don’t bother reading this stupid long post.
Hi,
I’ve got a bit of a head scratcher here and wondered what you guys would make of it.
I was called by a landlord to do a gas safety check on a property that is now at the latter stages of being sold and the buyers wanted the usual...
Apologies for the unusual question, as I am an interested DIYer.
The question is, why do you need a gravity coil, on a thermal store?
Surely, you'd get better flow rate from direct connections to the side, as there would be no friction and you could use 35mm or 42mm copper pipe, to a 2 inch...
Hi, I'm a newbie and need some advice please.
My 4 bed house has gas central heating with the Regular boiler (BG 330 set to 18Kw output) located in the garage. The boiler is connected directly to the header tank (vented system) and is also connected via a dedicated system pump to a thermal...
Hi,
I'm new here and have arrived on this forum as I have a question on the above.
I'm talking to a solar PV supplier about a 4kw system with which will come and Eddi controller which can feed 2 immersion heaters.
I'm a bit lost when it comes to the cylinders/thermal stores. We currently have...
So the plan is this. Currently I have all rooms individually controllable through programmable TRVs allowing me to heat only the rooms that are being used on different profiles during the day and night. So far so good.
But I have three main problems with my boiler.
1. there is no boiler...
Hi,
We have recently had a quote to fully supply and fit a Mitsubishi Ecodan System in our home...I would have liked to have a wood burner connected to it in order to subsidise the heat production and lower our electricity bills in the winter, however, with this configuration it is not...
Hello, got to change a PULSARCOIL 2000, anyone have experience of these, what would be a good replacement ?
have fitted a TRISTOR MANUAL FILL before to replace a combi cylinder, found it quite straight forward to install, and was impressed with quality and performance. But always ready to take...
Hiya new to forums so sorry if the wrong place.
I'm currently planning a thermal store installation for a new property being converted into a hmo .
I would like to zone every single bedroom and give the teanants a switch (like a light switch) which is also run into a tamper proof thermostat set...
Hi
I'm looking for a plumber able to connect the gas boiler to the thermostat, thermal store and valves.
Our previous plumber said it was the electricians job & left. The electrician said it was the plumbers.
We have all the bits, just not connected.
BS6 Bristol. Pm me for my mobile
Ta, Stephen.
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.