You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
tail
The tail is the section at the rear end of certain kinds of animals’ bodies; in general, the term refers to a distinct, flexible appendage to the torso. It is the part of the body that corresponds roughly to the sacrum and coccyx in mammals, reptiles, and birds. While tails are primarily a feature of vertebrates, some invertebrates including scorpions and springtails, as well as snails and slugs, have tail-like appendages that are sometimes referred to as tails. Tailed objects are sometimes referred to as "caudate" and the part of the body associated with or proximal to the tail are given the adjective "caudal".
Has anybody ever come across a bath/shower mixer which leaks from the tails? By this I do not mean where the tap connector screws on to the tail, but actually where the tail fits into the body of the mixer. This mixer in question is only a couple of years old. Views, anyone? :confused:
Hi all, what's a good solution for fitting a radiator which is slightly smaller than the one that came out, is there a nice fitting that tails out of the radiator into a section of 15mm?!!!!
I came across some fitted by British Gas, real chunky connectors but they look too much for the job.
Livvid
Thread
10mm
40mm
british gas
fitting
gas
job
merchants
plumbers
radiator
radiators
size
smaller
tail
valve
valves
hi i just installed three new rads and they are leaking on the lock shield side. is there sumthing im missing, i tightened then as fare as i can and they still leak and advice would be most gratefull.
nez
Thread
cold radiator
damage
hot rads
leak
leaking
pipe
pressurised
problem
tail
valves
vertical
whistling
yellow
I'm trying to fit TRVs to some old rads. and the rad has a 1" female thread, rather than the standard sized fitting. Has anyone come accross this before (probably all of you!) and if so is there a 1" inch raidator tail I could use, or suitable chrome reducer avaliable.
I'm really new to...
jlbreak
Thread
brass
copper
female
fitting
inlet
metal
plumbers
plumbing
price
radiator
reducer
stainless
system
tail
their
training
trv
valve
Hi, I have some new monobloc kitchen taps & they have flexi tails with a female threaded fitting with a flat rubber washer, can I simply screw them to an isolating valve (having discarded the valves olive & nut) ?
Thanks
Hi all,
small problem hopefully you can help me with. Fitting a double rad onto bedroom wall. Have bought a Bulldog TRV, which seems decent enough. Problem is, the two existing floor pipes have already been routed up throught he floorboards, capped off, and carpet etc fitted. I gave the...
seems one of the valve tails has snapped off , its a brass 3/4 tail.
what do you guys think? i was going to try and unscrew the whole bush and put in a new one but that sounds like a bit of a mission trying to unscrew that.
Can anyone help me please . I have been asked to replace a leaking rad on the first floor landing of a house that has about 17 rads . The new rad will be slightly shorter than the old one . To make a neat job of it I want to take up carpet , a floorboard or two then alter the pipework at one...
Hi,
I am replacing some old imperial radiators with smaller modern radiators. I don't want to move the old pipes coming up through the floor. I plan to fit right-angled Drayton TRVs and lockshields on top of the existing pipes and then run short lengths of chrome pipe between these valves and...
Hi all
Wonder if some one could help me. I have a set of taps that no matter what wont seem to tighten up? I have applied all the right washers in the right places and still doesn't tighten up. i am only hand tightening the back nuts as i can't get any tools in the get them any tighter. do i...
Woody123
Thread
advise
basin
bath
bath taps
brass
diy
job
merchants
plumbers
plumbing
problem
rubber
sink
stainless
tail
tap
taps
tools
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.