Search the forum,

towel

A towel is a piece of absorbent fabric or paper used for drying or wiping a body or a surface. It draws moisture through direct contact.
In households, several types of fabric towels are used, including hand towels, bath towels, and kitchen towels. At the beach, people use beach towels.
Paper towels are provided in commercial or office bathrooms via a dispenser for users to dry their hands. In households they are used for minor, precision, or particularly dirty jobs of wiping, cleaning, and drying.

View More On Wikipedia.org
  1. D

    Towel rail element

    Afternoon chaps and chappesses I have replaced a bathroom rad with a shiny new dual fuel towel rad (Kudox) My issue is that no matter what I do, I cannot get the element even hand tight - always about a quarter to half a turn off If I was to tighten fully, the pipe entry would be out of line...
  2. P

    Oil heating/ towel rail question

    Easy for those in the know but can someone advise me whether I can have a water filled bathroom towel radiator with il central heating. I am sure this is the case and think this is what is in the existing radiator atm. I assume you can only get electric and water filled towel radiators?
  3. T

    Changing towel radiator

    Hi all, im planning to change my towel radiator and have a couple of questions. I managed to remove the old one without draining the system as I could remove the rad but leave the rad's isolator valves (note these are from the radiator and not part of the copper piping). The problem is that...
  4. L

    Over tightened towel radiator

    I think I've overtightened the thread on top of the radiator. It's leaking. How do I replace the rubber seal, without draining the system?
  5. K

    fitting towel rail in bathroom

    I want to fit a new towel rail in place of radiator in bathroom. I have a Combi Boiler system. I have closed off both valves on radiator and removed radiator from wall. With the radiator off I opened both valves but no water came out of either. Is this normal with a Combi boiler and how do I get...
  6. M

    Micro bore pipe to a towel warmer?

    Hi all, a friend has just asked me to fit a small towel warmer in place of her old radiator in the bathroom. Problem is the old pipe work is 10mm bore and they are wider than the width of the towel warmer. She doesn't want the Lino ripped up so what's the neatest way of adapting the pipe work...
  7. M

    What centers for a 600mm towel rail?

    Does anybody know what centers I have to have for 1st fixing a 600mm curved towel rail? I seem to have 570mm in my mind for some reason.
  8. N

    dual fuel towel radiator questions

    Hi I am not a plumber nor experienced diyer and have some questions about ladder dual fuel radiators. The WWW seems to be a bit lacking.. :) 1) I was wondering how you choose your element wattage? Is it based on rad height vs element length or rad wattage vs element wattage? 2) there is...
  9. Neil T

    towel rads need a boost

    I've been to see an old customer who is having a problem with a couple of towel rads in a bathroom. It's a 'very' big old victorian house with 3 floors and basement (looks and feels like a hotel inside) and has 2 boilers in basement. Heating works perfectly for rest of house and customer...
  10. I

    Summertime heating

    Afternoon all, I'm working on a job where an old woman has been ripped off by some bodge artist the whole jobs a mess, any way I'm after some info from some if the more informed people on here, is it against regs to put 4 ,yes 4 towel towel warmers on the hot water circuit? The woman is trying...
  11. D

    Heated Towel Rail.

    Hi To everyone, this is my first post on this site hopefully I will get some help. As I have worked my way through my house decorating I have been replacing my old radiators for new. Because my house has a concrete ground floor the heating system runs through the first floor, running down the...
  12. N

    Towel Rail Plumbed from above

    Hi i am renovating a bungalow we have installed a new central heating system. long and short of the story in the shower area my plumbers installed a chrome flat towel rail, which we piped from above so basically the towel rail is upside down. We did this as walls are paramount egg box and didn't...
  13. D

    Towel Warmer on domestic circuit.

    Hi All, Any of you fitted a towel warmer to a hot water secondary circuit? I'd imagine they'd have to be specifically made for the purpose, not all towel warmers will be suitable because of the corrosive effect of the 'fresh' water yeh? I'm considering this for my own place but, to be honest...
  14. M

    fitting Tornado towel rails

    Hey has anyone fitting Tornado Towel rails? Any one else had trouble getting the clamp part of the clip that connects to the radiator the clip firmly?
  15. W

    Towel rail brands

    Hi, I'm replacing the famly bathroom and want to fit a heated towel rail in place of the rad, along with electric underfloor heating. The towel rail needs to be a fairly big rail (four women in the house :smilewinkgrin:) and I'm looking at 1600/500, but the range of brands and prices is large...
  16. A

    replacing an 10 mm microbore radiator with an 22mm towel radiator .

    What would be the best & afficient way to tackle this job.???
  17. jonnyswamp

    Towel rail elemant wired to motorised valve

    Is there a simple power closed, spring return open motorised valve I can fit to serve a towel rad with a heating element, so that when element is switched on, the valve closes and there is no circulation around rest of heating circuit This is on an open vented system and would be just on the...
  18. A

    Narrow Towel Radiator

    HI We had a vey small room downstairs and looking for an electric towel radiator (does not matter if its chrome white or any other colour) the size needs to be between 200mm wide or 250mm wide here and here , i have found one but not sure how to convert it to electric, does any standard towel...
  19. P

    Towel Rad valve leak

    Hi, got a leak from within the valve but can see no way of taking the cap off to see what's going on. End of cap looks to be moulded on. Any ideas?
  20. Riley

    At wits end with cast iron rad

    Hi chaps i hope someone can impart a bit of advice to me. Spent all all morning trying to fit a cast iron rad. All corners nicely sealed except one which has a very very slow drip. Have tried compounds, ptfes, lsx etc has anyone else got any ideas as it's driving me nuts. Thanks as ever matt
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock