You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
position
The missionary position or man-on-top position is a sex position in which, generally, a woman lies on her back and a man lies on top of her while they face each other and engage in vaginal intercourse. The position may also be used for other sexual activity, such as anal sex. It is commonly associated with heterosexual sexual activity, but is also used by same-sex couples.The missionary position is the most common sex position, but is not universally regarded as the most favoured one. It may involve sexual penetration or non-penetrative sex (for example, intercrural sex), and its penile-vaginal aspect is an example of ventro-ventral (front-to-front) reproductive activity. Variations of the position allow varying degrees of clitoral stimulation, depth of penetration, participation on the part of the woman, and the likelihood and speed of ******.
The missionary position is often preferred by couples who enjoy the romantic aspects of ample skin-to-skin contact and opportunities to look into each other's eyes and kiss and caress each other. The position is also believed to be a good position for reproduction. During sexual activity, the missionary position allows the man to control the rhythm and depth of pelvic thrusting. It is also possible for the woman to thrust against him by moving her hips or pushing her feet against the bed, or squeeze him closer with her arms or legs. The position is less suitable for late stages of pregnancy, or when it is desired for the woman to have greater control over rhythm and depth of penetration.
I know when installing an expansion vessel it must be connected to the system without any isolation valves. How is best to pipe in to the system so it can't be isolated. In the diagram below a potential way I was going to pipe in to a heat only boiler. It could be isolated by isolating the...
I just had a Comfort PM Recirculation pump installed to replace a much older and defunct pump. The plumber that did the work for me didn't have any experience with this particular model (98420224 up10-16 a pm bu/lc comfort pm autoadapt) but got installed where the older pump once was...
Hi, I had a Drayton ma1 mid position actuator recently installed as central heating had stopped working. Now my heating and hot water will not come on at the same time (with timed settings) and I have been advised that my thermostat is not working which is causing the problem (from the emergency...
Just wondering if anyone had any thoughts/ objections to position of expansion vessel. 3 zones on heating upstairs, downstairs and UFH. All zone valves on flow, pump on flow, loss header as well. Expansion vessel it situated on the return from the upstairs zone. I suppose it can’t be cut off by...
Hi everyone - my first time posting here, but I have used invaluable advice posted on the forums many times so thanks for that.
We have a 3 port valve in our heating system where the motor has died so I was just going to swap in a new head
The original one is a Travis Perkins ikon MA1 - it...
Hi
I have a faulty Siemens DVA3 3 Port Mid Position Actuator that needs replacing, Can get a Drayton MA1 quite cheap, will this fit in place of the Siemens ! .
Spike
We had a new bathroom built last year. Mould on the kitchen ceiling shows that it has been leaking for a while and the builder called in the plumber to investigate.
He took out a panel from the floor and found that the leak is on the connection of the shower waste to the 4" pipe. The waste...
Hi all
Just seeing if this is a common method of providing a boiler bypass thesedays as there seems so many ideas out there, years ago if we needed a bypass a gate valve was the answer but no longer classed efficient and others not suitable due to the smart pump.
The system is a sealed...
On the mid position valve am I right in thinking when no demand from heating and hot water the valve returns to default hot water position as the new one I've fitted stays in central heating with no demands
Thanks
The red one is sewage system. The workers put the vertical plumb where the big black dot is (зошто овде дупка во плоча за одвот) that means why there. There is a hole in the slab 30cm from each side of the wall. On the one side i understand cause there is a concrete beam, but on the other side...
Hi all,
We want to change the position of our boiler from the Kitchen to the outside cupboard at the front of the house.
The cupboard is 1m x 1m and 2.4m height and currently has a wooden door - so temperature wise will be close to outside temp.
We want to install a Viessmann Vitodens 100-w...
Hello,
When a Danfoss RAS C2 10 mm TRV is open to its maximum setting is this the same or almost the same as having a rad with no TRV ?.
And if it is open to this maximum and left open can a wall thermostat be placed in the same room and work effectively ?.
I'm in a property with a newly fitted...
Good morning,
I would appreciate any advice on the following: I live on the 2nd floor (top floor of building) and have a stopcock under my kitchen sink, one stopcock for water near the boiler in the kitchen and in the hallway in a high cupboard a cold water feed red gate valve. I want to know...
Hi,
We’re converting an old store/workshop joined to our house and installing a small shower room with the wastes connecting to the old clay pipe in the floor where the original toilet once was.
We needed to bring the floor up 100mm for insulation and had a plumber set the new waste pipes for...
Hi
I've just had a bit of work done in the house where we knocked down the wall between the kitchen and dining room. This wall had radiators either side. Two new radiators have been installed in the new open plan area. When the plumber came to fit the rads and balance the system he was unable to...
Excuse my wonderful drawing.
Someone put a gate valve here. If I've used the wrong symbol for a valve forgive me you'll have to imagine the right one.
There isn't one anywhere on the cold feed from the CWSC.
Since - if closed this isolates the water in the cylinder from the open vent - my...
hi guys. I came across a Baxi 105HE today and was trying to figure out whether the flue position was within MIs. I’ve attached a picture but looking in the book I can’t see an issue. Any advice will be appreciated.
Im going to be removing an old sink from one wall and re positioning the new sink on an adjacent wall
At the moment the hot and cold supplies come in through the wall and branch right for the existing sink.
I need to modify these so that they come in and head straight to the direction of...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.