You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
level
LEVEL is a computer and video games magazine originating in the Czech Republic with branches in Romania and Turkey. These three brother divisions occasionally exchange content. In addition to publishing the magazine, LeveL also organizes many yearly gaming competitions for players in two of the countries (Romania's pro-gaming sponsor being the PGL - Professional Gamer's League); it is one of the biggest Turkish sponsors of international gaming contests (such as WCG).
LeveL was founded by Jan "Beast" Tománek in 1995 in Czech Republic. Its first issue was released on 24.01.1995. The current LeveL editor-in-chief is Michal Křivský (replacing Petr Poláček).
Hi I am new to the forum, this is my first post. I apologise if its in the wrong thread and if its been answered.
Can anyone please advise me what are the recruitment cycles assuming there is a general one for the sector, so that I do not waste time.
Any practical advice will be appreciated...
I have made some adaptations to the layout of an existing open vented one pipe system. The pump is now some 6 or 7 metres away from the boiler. The cold feed is on the negative side of the pump as is the expansion pipe. The order of fixing is expansion pipe - cold feed - pump. When the pump...
Hi all
I’m posting a new thread to my first a couple of weeks ago. I’m at my wits end trying to sort a leaking high level cistern that is leaking from the base where the flush pipe connects. I have already replaced the syphon flush with a new one (Dudley) . The issue is the diameter hole size of...
Hi all. Today I attempted to fix an old leaky high level cistern that was leaking from the base of the cistern. I replaced the cistern flush (Dudley) but noticed the hole diameter on cistern was quite large compared to the inlet pipe ( circa 48 mm cistern hole vs 32 mm of inlet pipe) after...
Hello,
I've done the C&G Level 2 in Plumbing Studies. I'm currently working as a plumber's mate (part-time). Eventually, I'd like to become Gas Safe registered and work on LPG - at leisure sites and maybe on boats, etc.
Any comments or advice on how best to get there? Should I do the Level 2...
Hello everyone!
I’m currently a 24 year old level 3 NVQ plumber from the Manchester area, I am starting a gas training course next month which after/during the course I am required to find work experience where i will be supervised by a gas safe engineer. For my portfolio, i must provide a...
Hi guys, I don't know if any of you could help me out but I cannot find any revision material and/or mock exams for the City and Guilds Electrics exam (6189-025), if anyone has any links, documents or other material and could possibly send, it would be very much appreciated. Cheers
Asking if there are any experienced plumbers (In Kent) to help me complete my NVQ Level 2 assignments.
Please PM if you are available, would greatly appreciate any help.
hello,
I’m currently attempting (with very little knowledge) to renovate an old
JAPKAP toilet cistern.
I’ve so far fixed the wooden box, the lead is fine and flush arm is being re-cast.
However I’m really unsure of how to repair the flush pipe (I think that’s what it’s called) as it was...
we currently have existing and new middle size and large size projects in London and Cardiff Center require all level plumbers to join us, to provide new and maintenance. ideally part time will be welcome.
it will be appreciate if you can drop me a pm with a short introduction. we can set up a...
In the last few days we've had high water level in downstairs toilet.
The first few flushes are good and waste flows away but eventually the water level rises in the pan to perhaps half the height of the pan and takes some hours to drain away.
Last night I poured 6 large buckets of hot water...
Hey just brought a Stanley self levelling laser level as I used imone from a chippy the other day doing some heating drops. Just wondering if any of you guys use them on a dayly basis if so what on. Cheers guys.
I wonder if anyone can help me. The oil level in the BM valve on the side of my Rayburn seems to have dropped as it now doesn't see to be high enough to enable the oil to reach the wicks in the burner unit. Oil flow appears fine but the flow stops before it reaches the main part of the burner...
Hi,
Is it OK to use a ball lever as a mains stopcock? ive read a few old threads but none of them seem to have definitive answer! also can you use plastic / push fit off a mains stopcock or does it have to be copper?
How can I upscale my level 3 diploma to a NVQ. I am self employed and want to upscale my bpec level 3 diploma.i have been quoted silly prices from local colleges and wanted to k ow if there is anyone operating as freelance who can do this at a more affordable price.
Hi everyone,
I re-arranging my kitchen and would like to install the washing machine with the following setup. I will cut a trench in the concrete below the wooden floor to fit the hose for the waste.
Do you think that would work?
Thanks for your help and advice. :)
I’m considering investing in a laser level. I’m thinking it could come in useful and possibly save time for pipe layouts and boiler installs. At the moment I just use a spirit level. Anyone here using them and which do you recommend?
Cheers
hi everyone I’m doing my nvq 2 I have done my level 2 deploma. Currently work five days but doing my nvq at weekends. I might have somone to help but if that fails is there anyone in the Bristol area that can help me get threw it .
Many thanks
James
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.