You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
incoming
Incoming is a 3D shooter video game developed by Rage Software and published by Interplay. The game was first released for Microsoft Windows in late 1998, and was followed by a Sega Dreamcast version, which was released in Japan on December 17, 1998, in Europe on October 14, 1999, and in North America on September 15, 1999. Set in the near-future of 2009, the game primarily revolves around controlling vehicles and turrets to fight alien invaders of Earth in one of the campaign modes, the arcade mode, and with or against another player. Some levels include brief real-time strategy segments.Praised for its then-advanced graphics and sound, the game was generally well-received on the PC, though the critical response was less positive for the Dreamcast version. A sequel entitled Incoming Forces was released in 2002 exclusively for the PC. An arcade version of the game, utilising a unique hardware interface, was released in 2003.
Hey all,
I currently have a turn type valve on the incoming water supply, not the lever type.
My plumber suggested changing it to a ball lever (full bore fitting) and it will be less resisitive so could help get our flow rate up.
I have done a quick bit of research and assuming i have a gate...
allesclar
Thread
designed
different
flow
flow rate
incoming
lever
main
pressure
tap
types
valve
valves
Hello everyone,
New here but this is driving me mad.
We had a vented gravity fed water system and the shower was fed via a mains powered water pump and storage water tank, with inlets for both hot and cold fed to a mixer in the bathroom.
In order to free up space in the loft and give better...
allesclar
Thread
cylinder
incoming
pressure
problems
should
shower
shower pressure
unvented
vented
Hi
I have a problem with an internal stop-tap which has seized open (tried penetrating oil / spanner etc - the spindle will move but only a little bit back and forth). There is no evidence of an external stop tap in the pavement although I have called United Utilities to do a trace and locate...
Ok, so today it's seems I've made a massive cock up. A while back a client asked me to recommend a combination boiler for installation.
I recommended a Worcester 34cdi, that seemed to be suitable for his property, 30kw CH, 34kw HW, however the client had loads of cold water flow so I said he...
Hi All
I wonder if any of you experts can help.
My house is about 13 years old and has 3 toilets all of which at times suffer from the ball valves leaking.
This can be as much as twice a month. However after cleaning out the valve it then works fine for a time.
On every occassion the reason...
ray1960
Thread
house
incoming
leaking
mains
oil
toilet
valve
valves
Hi, Im going to be installing an unvented cylinder to a property next week. I've got the cert and hand books but I can't see any info on pipe sizing for the feed! The ones I've done in the past hve all had a 22 mm rising main, this one has a 15 mm. The pressure and flow rates are good. Will it...
Hi all! I am new here, and I would really appreciate your help.
I live in an area where the water pressure is high (>8bar) and unstable (may range between 6bar to 10bar).
How can I regulate the pressure so that it is stable at around 6bar? Would a reducer do the job? Suppose a reducer reduces...
andgeo
Thread
incoming
pressure
reducing
valves
water
water pressure
Hi guys, I hope you can offer some advice,
We have stripped out our old kitchen, and relocated it in a new extension, the water main comes in at the back of the old kitchen units.
I have attached a photo showing this, along with and a length of 15mm copper which runs 1.4m to the outside wall...
Quick question for you lads that have had any similar experiences. Working on a shop this morning and have had to shut main off in street due to a leaking stopcock and it has blown outside. There is a small fountain of gushing water outside the shop now! Do water board charge to repair this as...
Looking for advice in regards to a Vokera Linea Max combi which has recently developed a fault whereby the hot water intermittently isn't always very hot. Every now and again, a bath of water or shower runs lukewarm or when turning a hot water tap on, it takes longer than usual for hot water to...
Hi I was looking at a home buyer report for a friend, It stated that the incoming mains supply should be replaced with alkathene and gave it a condition rating of 3.
Is that because the incoming mains supply is a lead pipe or is there any other reasons for it to be replaced.
thank for your time...
Hi, I have noticed when the incoming main valve is fully closed it is still passing water possibly as much as 10% of normal flow. This valve is possibly 20 years old. Should I replace with what? The valve in question looks like an ordinary brass tap. Is this correct for mains isolation? if...
mikehardy
Thread
closed
cold
cold water
incoming
isolation
main
merchant
passing
replace
should
valve
washer
water
I've recently sold my house (stc) and my buyer has flagged up an issue with my incoming water pipe. I have had a plumber round as the buyer wanted it lagged as it comes in via an outside wall and not through the floor. My plumber didn't think this was necessary but did it anyway, after 3 years...
Evening all! Went to look at a bathroom today for one of my landlords. In a ground floor flat direct fortic cylinder about 600m off floor pressure really poor. Is there a way to increase flow rate. Thought about a pump but obviously the tank above is really small so may not be able to cope with...
Hi All
Have you any idea's why it is that 75% + of all the un-vented hot water installs I go to, are incorrect & do not meet Part G Building reg's (& I have seen a lot in my time) don't get me wrong some are silly things like discharge pipes too long or running up hill but others are down right...
hi all
have a quick question for people in the know!!!!
have a thermo basin mixer that when turned on to the cold setting is flowing with a temp of 23-24c
the hot temp is set ok at 42c no problem,
hot temp is coming into tap at 62c
cold temp coming into tap at 18c
now thw client is saying the...
pete37a
Thread
basin
cold
coming
heating
hot
incoming
mixer
question
setting
should
thermostat
thermostatic
i have a leak to goto on an icoming mains which is made of a black plastic!! does anyone know what this stuff is and where can i get fittings for it??? looks to be around 22mm....never seen the stuff before!!
Hey chaps, i am having difficulty trying to connect into a couple of nipples on some old iron pipe. Its not the main actually , but the hot. I have bought all the sizes of brass from toolstation, and none of them seem to fit.
Are there like old imperial sizes of iron?
I am lost as to where to...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.