Older boiler services?

[macka09]

Hi folks. When you guys go out to service an older boiler do you actually strip and clean it regardless or do you take flue readings and inlet pressures before proceeding? Reason I ask is because some MIs state new gaskets and seals are required once the old ones have been disturbed??

 

[ShaunCorbs]

strip and clean main burner area and then oldschool it eg

burner pressure
flame pic etc

 

[macka09]

strip and clean main burner area and then oldschool it eg

burner pressure
flame pic etc

So what Do you do then if one of the seals is no good once you’ve got the burner apart?

 

[ShaunCorbs]

what boiler?

 

[AMGasServices]

So what Do you do then if one of the seals is no good once you’ve got the burner apart?

Ask the customer to send you a picture of the boiler and take a set of seals with you as a precaution. Forward planning saves the customer the headache and you get the job sorted first time.

 

[macka09]

I ask this question as I don’t work for myself I just get sent to the job. Personally, what you’ve advised is exactly what I would do.

Boilers like a potterton 60 or ferroli f24 or Baxi 33he? Anything old really rather than a 25si or something.

 

[firemant]

Hi folks. When you guys go out to service an older boiler do you actually strip and clean it regardless or do you take flue readings and inlet pressures before proceeding? Reason I ask is because some MIs state new gaskets and seals are required once the old ones have been disturbed??

That sounds a bit unusual on old boilers, normally more of an issue with new stuff.

 

[macka09]

That sounds a bit unusual on old boilers, normally more of an issue with new stuff.

The new stuff we put in is always a Worcester, which if the fan pressure is ok it doesn’t require a strip down. Reading up on the Potterton it says it needs a new gasket if disturbed. That’s why I ask really as I’m sure most guys wouldn’t be arriving with new seals or gaskets to every boiler service ?

 

[Millsy 82]

I ask this question as I don’t work for myself I just get sent to the job. Personally, what you’ve advised is exactly what I would do.

Boilers like a potterton 60 or ferroli f24 or Baxi 33he? Anything old really rather than a 25si or something.

When you said old I thought you were going to say things like a Mexico, kingfisher, Concord wrs.

Older boilers were never a problem for seals it's new boilers that require seals and it's a pain. As some say every year others 3 years others when they need replacing.

 

[firemant]

The new stuff we put in is always a Worcester, which if the fan pressure is ok it doesn’t require a strip down. Reading up on the Potterton it says it needs a new gasket if disturbed. That’s why I ask really as I’m sure most guys wouldn’t be arriving with new seals or gaskets to every boiler service ?

Which Potterton ? The Baxi equivalent ones dont beed new seals.

 

[macka09]

Which Potterton ? The Baxi equivalent ones dont beed new seals.

Suprima 60?

 

[Gasmk1]

you only need to change or fit new seals on suprima if damaged, but you wouldnt carry them unless you serviced a lot of them.

 

[macka09]

you only need to change or fit new seals on suprima if damaged, but you wouldnt carry them unless you serviced a lot of them.

That brings me back to my original question in respect to, what do you do if you haven’t got them and you’ve stripped it and can’t get them off the shelf?

 

[Aire]

That brings me back to my original question in respect to, what do you do if you haven’t got them and you’ve stripped it and can’t get them off the shelf?

Condem the customers boiler and turn the gas off

 

[Last Plumber]

When you said old I thought you were going to say things like a Mexico, kingfisher, Concord wrs.

So did I