Search the forum,

washers

A washer is a thin plate (typically disk-shaped, but sometimes square) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such as a bolt or nut. Other uses are as a spacer, spring (Belleville washer, wave washer), wear pad, preload indicating device, locking device, and to reduce vibration (rubber washer).
Washers are usually metal or plastic. High-quality bolted joints require hardened steel washers to prevent the loss of pre-load due to brinelling after the torque is applied. Washers are also important for preventing galvanic corrosion, particularly by insulating steel screws from aluminium surfaces. They may also be used in rotating applications, as a bearing. A thrust washer is used when a rolling element bearing is not needed either from a cost-performance perspective or due to space restraints. Coatings can be used to reduce wear and friction, either by hardening the surface or by providing a solid lubricant (i.e. a self-lubricating surface).
The origin of the word is unknown; the first recorded use of the word was in 1346, however, the first time its definition was recorded was in 1611.Rubber or fiber gaskets used in taps (or faucets, or valves) as seal against water leaks are sometimes referred to colloquially as washers; but, while they may look similar, washers and gaskets are usually designed for different functions and made differently.

View More On Wikipedia.org
  1. B

    New main storage tank

    Eh when i were a lad i was called frank the tank on account of i was small and slim and got all the MST.s so when i did one yesterday i was disappointed that tank cons have so little sholder barely 3-4mm i cut the hole undersize and reamed it but plastic tanks go brittle over time and so the...
  2. B

    baxi rubber washers

    just something for those of you that fit baxi/main/potterton boilers they were coming with rubber washers for the gas but now they are fiber instead i had to ring BAXI to check as something looked amiss remahas time and efficiency people may have dropped them to save a few bob?anyway theres no...
  3. M

    heatmax gas probs

    any one had any problems with the gas nuts on the heatmax or duotec coming loose after a few days had 3 up to now and mate tightened one on a boiler and the same with him its a bit scary so gunner ring baxi
  4. T

    Old council Supatap

    Can any body tell me where i can buy a pair of basin supataps. My uncles cold tap has siezed, and i snaped one of the thumb lugs off !! Been scanning the streets today for a council van, sure he will have a pair on board. Also scanned net and can only get washers for this type. Any ideas would...
  5. L

    Fitting new Kitchen Tap

    I have a problem i bought a new tap but the hole is a fraction to big what can i do to remedy this iv tried to buy large washers no luck can any one help me Tony
  6. G

    brass drain cock washers

    Can you get new rubber washers for drain off cocks i had to drain my cylinder as the cold inlet was leaking. i have tightened the drain cock as much as i can but its still weeping so i drained the cylinder again and stripped the drain valve and the washer had perished and all the washers i had...
  7. E

    1/2 inch nylon tap washers

    does anyone know where i can buy the tough nylon washer that comes with the conex tap extension, i have a stash of plastic washers but they dont seem to be man enough for the job, the washer in the picture is white nylon and about 2mm thick. Thanks for looking
  8. J

    Fibre washers

    Hi all, does anyone know where I can find fibre washers with an ID of 21mm and an OD of 32mm? thanks, JuvUK
  9. O

    Fiber Washers

    I never seem to get these to work for me. They seem to keep weeping untill you nip it up enough to stop that then about 12-18 months later start to leak. When you undo the joint the washer has turned to mush. What am I doing wrong? Where as if I replace it with a rubber washer then I can almost...
  10. P

    Baxi washers

    I have just been charged £2 each for the tiny washers Baxi part no.248735 that connects the pipes to the dhw differential valve, and this was trade. Does anyone have a cheaper source for these (Gold plated washers).
  11. K

    Washers

    Just a quick query are the rubber washers used on gas fittings any different to that used on say water fittings? Do they have to be resilient to natural gas etc Thanks
  12. R

    equilibrium valve - whats the bit in the washers for?

    Hi when you take apart a equilibrium valve eg torbeck compact, when you look at the washer there is a minute pin and a big pin gong through them. they have a place to sit in the valve seating - what are they for? Many Thanks
  13. W

    Washers for 1" stopcocks - please help

    Hi. Can anyone out there please advise me where I can get a washer for a 1" BS1010/2 stopcock. Everywhere I have tried only stocks up to 3/4". Plenty of merchants stock the stopcocks but no spare washers for them! Thanks
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock