room stat

A mechanical room, boiler room or plant room is a room or space in a building dedicated to the mechanical equipment and its associated electrical equipment, as opposed to rooms intended for human occupancy or storage. Unless a building is served by a centralized heating plant, the size of the mechanical room is usually proportional to the size of the building. A small building or home may have at most a utility room but in large buildings, mechanical rooms can be of considerable size, often requiring multiple rooms throughout the building, or even occupying one or more complete floors (see: mechanical floor).

View More On Wikipedia.org
  1. R

    Salus Wireless Room Stat

    Can anyone give me some advice please about wiring in the receiver box for a salus wireless room stat? I'm wiring in to a Fagor boiler which states that it has to be a Volt free connection. Therefore do I just wire in L and N from the reciever to the boiler connection? Or do I also have to...
  2. R

    Room Stat Installation

    Hi guys I've been asked to fit a wireless room stat to accomation with a Fagor Feb 20E combi boiler. Can I buy any wireless stat for this boiler or does it have to be a certain one? Also is it easy wiring in the recever to the boiler? Cheers Rob
  3. J

    Thermostatic radiator valves - a legal must?

    Hi - a heating engineer told me that they have to legally fit TRVs if they do a boiler job- this true - wheres the legislation to prove this? Thanks JK
  4. H

    Room Thermostat

    Went on the Honeywell wiring course today and remembered about people querying the height of room stat (part P , Part M etc). The instructors said room stat had to be set at 1200mm from floor max(same height as switches etc) to comply with regs etc.
  5. B

    Part L compliance

    Hi All, I am a new member and would like to thank in advance anybody who can answer my question regarding the fitting of thermostatic radiator valves I have previously read as a guest, a request for similar advice but was still unsure of the advice given, so I am sorry for having to elicit the...
  6. W

    Wiring For New RF Room Stat?

    I'm having a few problems figuring out the (basic!) diagram and instructions that come with my new Danfoss RET-B-RF RX1 wireless room stat. Its the type with just stat function, ie. no built in programmer. I have a Y Plan vented system with Potterton EP3002 programmer. This is the diagram for...
  7. C

    Best place for a room stat in a two bed flat?

    Hi i posted a topic on here before before thanks for answers. What is the best place for a room stat in a two bed flat? Mine is in the hall, in the coolest area. I notice it doent switch on and off tho.
  8. M

    installing a programmable room stat to a radiant sirrus boiler

    i have a job to install a programmable rf room stat to a radiant sirrus boiler,now i've never come across one these boilers before and was looking for some guidance on the wiring for it and i'm a bit unsure. have any of you fuys out there dealt with one of these??
  9. M

    heating problem

    I have a combi boiler (about 18month old) I have a separate thermostat which is in the hall but when I turn the thermostat below 20 the heating goes off altogether -I can't understand why this is happening any ideas please? Thanks Merlin 77:)
  10. R

    Wireless Room Thermostats

    Hi chaps, I've been asked to fit a wireless room stat for a customer. I've not done one of these before. Are they easy to set-up and get going?? Cheers rob
  11. D

    central heating problem

    I have been trying to repair my sons central heating system i have installed a new pump, checked tri-valve manualy. the boiler fires up and the pipes get hot either side of tri-valve but boiler cuts out befor rads get warm. all rads have been bled, hot water is working but no heat in rads...
  12. P

    room stat wiring

    hi all some advise needed our central heating system does not have a room stat so boiler keeps coming on and off every few minuets. so i have ordered a wireless room stat. can it be wired strait in to the programer as i have not got a wiring diagram for programer it is a potterton ep2000 is...
  13. A

    Basic Room Stat needed

    Just after a basic room stat, needs to cover the ancient potterton one I have now that is 95mm wide and 70 odd mm high. It must be at least 95mm wide as the room has just been decorated and there will be a hole either side of the thing if not. Does anyone know one that will do the trick...
  14. C

    wiring an eco et3 rf room stat to a glow worm betacom c 30

    Hello fellow plumbers. can anybody give me some advice on how to wire this room stat. http://www.glow-worm.co.uk/products/...structions.pdf. if you look at this page it only shows one wire going into the block but i want to know do you put both wires from the transmitter into the block and which...
  15. R

    potterton performa room stat

    Hi all a bit of help please i am wanting to fit a room stat to my potterton performa 24 eco. Am i correct in saying that all that is needed is a twin core cable connected to the looped terminals on the boiler and then fitted to the live & sw live on the stat?
  16. S

    room Stats

    Can anyone tell me the difference between a changeover roomstat and a on/off roomstat ?
  17. eagleeye

    Room thermostat

    Hi guys hope you can help me here. I have just finished a new heating system a old ladies bunglow. It is a friend of my dads that he looks after. anyway, she is 96 years old and is visually impaired, therefore the standard programmable room stat that i put in is no good for her. She needs...
  18. G

    Blind/disabled friendly room stat

    Hi, i,ve got a central heating system to install and the customer is blind, so i'm looking for a room stat that is designed to be easy to use for people with sight problems. im sure such a thing must be made, although im having trouble finding such a thing on the internet, does anybody know...
  19. S

    Programmable 7 day room stat

    Hi, I have underfloor heating (wet) and each of the zones is controlled by a Danfoss TP5 Room stat (With 2 wire feed). One of my TP5s screen has broken and I'm therefore going to upgrade to a 7 day programmable one with "Smart start" or "Optimum Start". Which Room stat would you recommend...
  20. F

    new Room stat

    got myself a new room stat Horstmann DRT 1 to replace the old switchmaster bellows type it works a Potterton Netaheat electronic 10-16 , through a switchmaster 400 the control knob behind the panel is set to 2 (what does this control?) put the new stat on this afternoon, and set it to 19.5...
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock