Attended a job where an external'y run 32mm plastic waste pipe complete with compression elbow had cracked and disintergrated all along it's length. Including the elbow. You could gently press any bit of it with your finger and it would literally crumble to nothing. Consistancy of egg shells...
Hey all,
Whats your recommmendations on using copper push fit on rad changes. The reason being is that they have the very expensive wallpaper (apparently irreplaceable) behind so I really don't want to get into the situation of accidentally leaving a heatmark on it even using a heatmat behind...
The age old question! im sure this has been discussed many times before but what is your favorite brand of plastic / pushfit?
Personally i use Speedfit since my normal merchants only stock that and poly plumb but if convenience of supply wasn't an issue i would go with hep20 cos there pipe...
Hiya,
The mother-in-law has Homeserve Insurance to cover bits and bobs, the last leak she had was just before christmas to the supply pipe to the house, halfway across the lawn.
Homeserve came out, stopped the leak, then went away.
2 days ago I noticed that water was welling in the same spot...
Hi all
I have used copper pipe throughout my extension build - tails up through the floor were capped with push fit plastic as it was much easier than using compression stop ends. The rest of the radiators were fitted and 'made live'. I warned the joiners that the system was now filled - no...
Hi, I'm a novice when it comes to plumbing. I've used compression fittings in the past, and have applied jointing compound.
With push-fit copper fittings, do you still need to use jointing compound?
Hi,
Is it safe to solder a copper joint onto a length of copper pipe that has a plastic push fit (twist type) connector on the other end of it? Is there a minimum safe distance of copper pipe between the plastic joint and the hot end? I'd like to replace some plastic CH joints with copper...
Someone on another thread on here mentioned that Hep20 and Polyplumb are better fittings and pipe than Speedfit. Is this true, are certain pushfit brands better than others?
I need help before i lose my mind lol. I have used 5 of these pushfit fittings now on my bathroom and all have leaked.
Please tell me what i am doing wrong.
They are leaking from the base of the tap, I have hand tightened them and they leak. I have tightened them tight and they leak, I am...
womble
Thread
bathroom
compression joint
condensation
costs
fitting
fix
help
hose
internet
leak
merchants
pipe
problem
pushfit
rubber
save time
scenario
seal
sealed
tap
taps
test
washer
water
work
Im going to sound like a right novice here but bare in mind i have no plumbing knowledge so please be gentle. My Question is this. Can you fit Plastic pushfit to copper tube? And without any trouble, Would it just be like connecting plastic pipe?
womble
Thread
10mm
copper
damage
fitting
gas
novice
pipe
plastic
plumbing
pushfit
tap
trade
water
work
anyone used them copper pushfit fittings are they any good.
got a job where i have 2 tails coming out of the wall connected to plastic behind/inside wall i want to T off the tails flow and return to put in a new rad.
thinking the pushfit copper might be a good option in this situation i...
pauls
Thread
cheap
cold
connect
copper
fitting
flow
inside
job
kitchen
pipe
pressure
problem
pushfit
tap
test
valve
wall
Hi guys new to this forum so be gentle with me :D, we are building our own place and I'm looking to run a 22mm hot water loop.
The layout is:- at one end of the building is a HW cylinder in a Grd Flr Utility room with an ensuite above it and then 16m down the other end of the building is a Grd...
21stcenturyelec
Thread
22mm
bar
bathroom
building
ceiling
cold
copper
cylinder
flow
flow rate
hot
hot water
mains
mixer
pipe
problem
pushfit
shower
solar
supply
tap
toilet
water
Hi All
I'm a 'plastic pipe virgin' about to embark on my first non-copper project. I'll probably be using jg speedfit as they are available locally. I noticed that you can get fittings (elbows etc) and also pipe inserts. Question :- do the fittings normally come with pipe inserts (when in bags...
wakeyomega
Thread
air
bag
combi
combination
copper
flame
hot
job
merchant
pipe
pipes
plastic pipe
pushfit
question
whats
work
Hello Plumbing Forums
I am having a new central heating system installed at my house. The new system will consist of a worcester bosch greenstar 27 cdi combi boiler, 12 no radiators (compacts), 11 thermostatic radiator valves. The system will be sealed, unvented.
The pipe work will be mostly...
hns123
Thread
boiler
bosch
central
central heating system
combi
combi boiler
concrete
copper
heating system
kitchen
pipe
plumber
plumbing
pressurised
pushfit
radiators
sealed
system
thermostatic
under floorboards
unvented
valves
worcester
work
hello all, just wanted your opinions on which brand of push fit fittings are best from your own experiences? ive not used them a great deal, my two local suppliers are screwfix and toolstation but ive been advised not to use the jg speedfit that screwfix sell and am not sure about toolstations?
wally5460
Thread
boiler
brand
burst
ceiling
central heating system
fitting
free
hep2o
hot
hot water
parts
pipe
pipes
plumber
problem
push fit
pushfit
radiator
shape
speedfit
tools
valves
wanted
water
which
hi there,
i am a kitchen fitter who has only recently converted to using plastic pushfit pipes and fittings.
they work very well when incorporating the pipe inserts.
however, they are quite expensive, when compared to the end feed i was used to using.
does anyone know where i can buy big...
Unregistered
Thread
15mm
branch
buy
costs
find
fitting
fittings
flexible
free
head
inside
installers
jobs
kitchen
kitchen fitters
pipes
plumbers
plumbing
price
pushfit
register
stock
system
trade
website
work
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.