You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
horizontal
In astronomy, geography, and related sciences and contexts, a direction or plane passing by a given point is said to be vertical if it contains the local gravity direction at that point.
Conversely, a direction or plane is said to be horizontal if it is perpendicular to the vertical direction.
In general, something that is vertical can be drawn from up to down (or down to up), such as the y-axis in the Cartesian coordinate system.
Hi everyone,
I'm currently installing a new bathroom and using Saniflo to pump all the waste to the soil stack. However, the waste pipe has a vertical lift of about 40cm at the very end where it joins on to the soil stack. I've read everywhere that the vertical lift should always precede the...
slantsaman
Thread
after
horizontal
lift
pipe
saniflo
vertical
waste
waste pipe
Hi guys
Really need some help...
We have a Warmflow 70/90 Oil Fired Combi Boiler. We're looking at putting a porch/conservatory on to the property, right where the flue exits the external wall.
I have a couple of solutions for the flue but I REALLLY need to know what the maximum horizontal...
Have 2m height and require a 500L unvented cylinder. Most will be just under this height so probably best if I go for a horizontal so it's not too tight.
Question is, is there an unvented cylinder with solar (future proof if I install solar), indirect (heated by gas boiler), horizontal and 500L?
DesDixon
Thread
cylinder
cylinders
height
horizontal
solar
unvented
unvented cylinder
a hi there if anyone knows where I can get one of these it would be greatly appreciated. I have been to a couple of local plumbing merchants who don't have them and googled for hours. It's for my sink, I have limited room under my sink as I have pull out waste bins underneath. The bins are...
Hi,
Have had new system installation done 2 years ago and all has been well until now. Vaillant Ecotec plus 637, sealed system, pressurised water cylinder, dual heating zones, external controls, secondary hot water return ring, 26 rads Victorian house, all new pipework, hard wired CO...
Gillbe
Thread
bosch
compatible
ecotec
ecotec plus
external
flue
horizontal
installer
plus
right
system
vaillant
worcester
worcester bosch
Hi,
(wow my browser really doesn't like me typing in here. I have to wait 1+ sec after each key press.
othewseis happens if I type nomal ped - otherwise this happens if I type normal speed)
So, anyway, I'll keep it short...
Am I OK with attached ensuite layout? (Plan view and Side view...
Apologies if this has been covered before but I searched on "Telford" and saw nothing. This relates to events 12 months ago when we had a problem but I never resolved it to my satisfaction so I thought I'd run it past the brains trust:
We have a horizontal Telford Tempest 150ltr being driven...
Hi,
I did ask this question a few days ago, but I wasn't quite sure from the answers if what I was doing was ok. So I'm asking again with a specific question. This is sketch of the branch pipe I am proposing to fit.This is a 40mm bath waste pipe.The total fall is much higher than the building...
My son is putting in a bathroom upstairs in a small victorian house. A plumber has installed a soil stack, and wc connection a while ago, but we now need to connect up a sink waste and a bath waste into that soil pipe. Where the waste pipes would naturally come out of the wall around floor...
Hi all,
I need some advice installing a new toilet. Please tell me if you think if it is likely to create blockage if I install an horizontal rigid pan connector with multiple bends; it is about 1.5 meters long from the toilet to the vertical pipe, and I have limited gradient (maybe 15mm if I...
adamlondon
Thread
behind
bends
connector
horizontal
multiple
oil
pan
pan connector
soil
through
toilet
Hello, I would appreciate some advice if anyone could spare the time...
I have a soil pipe running horizontally (with correct fall) for 1m before it exits the house. Coming in from the side I have a 40mm which carries the waste from a bath and sink. This needs to connect to the soil pipe.
The...
My plumber has come up with this solution to an admittedly tad complex piping challenge. But I cannot see how the horizontal section will not result in waste accumulating there, on the main channel temporarily due to lack of maximum flush pressure; and on the inspection arm simply as it's a...
Ok, i have a 3 WC's, 2 urinals, 4 wash basins to install in a restaurant the soil pipe runs horizontal in a void. Just wondering what is the maximum length it can be? the length it needs too be is around 8 meters. If I'm correct the maximum is 6 meters? Also the stack what is in now is vented at...
Just been picking up on some work another plumber left unfinished and need your views. The ex plumber installed a grundfos homebooster 4.5 bar unit and a 300 litre potterton gold uv horizontal cylinder. This supplys 4 showers, kitchen, and 2 toilets with basins. Flow rate is about 25 litres a...
Hi guys
any one know if you can run this pump horizontaly .............. I currently have an old selectric 15 / 60 working this way on the c/h been like it seven years or longer....... no probs....... just thinking of replacing pump with new one Alpha 2 and will be easy if it...
Hi Guy's
I currently have a grundfos 15 / 60 selectric central heating pump that is laid flat to the floor , so workng horizontaly and on the c/h return ........ now, as it is working fine and has been for seven years ( and longer ) do you know if the new grundfos pumps ( Alpha 2)...
Looking for a bit of guidence on how's best to run wastes for bath and basin
Due to a remodel I now have no other option but to tee the basin waste into the bath waste be for it goes outside to the soil stack
I have managed to find a route for the waste plumbing that will give sufficient...
reeves1985
Thread
advice
basin
before
horizontal
pipe
waste
waste pipe
which
Evening all , right heres my conundrum . I have made a few stainless rads for customers before , yes made welded etc not just stuck some fittings on !
My current customer wants me to make a towel rad using 28mm copper tube , the desing is simple enough as a series of bends , the down side is...
Dusty23
Thread
copper
element
heating
horizontal
standard
towel
towel rad
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.