flexi

  1. H

    flexi

    1/2 inch x 15mm speedfit flexis 300mm long for sale open to offers
  2. P

    Baxi 105e Pressure Problem

    Hi to all that can help, the above boiler when operated pressure rises to over 3 bar and expels from the prv. I have charged the vessel up and there was a new prv fitted recently. The valve on the vessel has air coming out of it so is it possible for the membrane to wear inside the vessel and...
    • purpleorange
    • Thread
    • baxi could flexi pressure pressure problem problem system vessel
    • Replies: 22
    • Forum: Plumbing Jobs | The Job-board
  3. P

    Glow worm flexi com F9

    Hi all, Just come back from looking at a flexi com i fitted 2-3 years ago, keeps going out the bloke says, F9 every 2 -3 days, resets goes. working when i got there cont find nothing at all? fitted alot of these over the last few years and had no probs, Anyone else had the same?
  4. S

    expansion vessel flexi hose.

    the braided flexi hose split and started leaking in the early morning, should i replace the flexi hose like for like, the external EV has a fitting of 3/4" and the fitting to the other end of flexi hose is also 3/4" any comments and thoughts are welcome.
  5. J

    Vokera syntesi 29E

    Hi all, I have a Vokera Syntesi 29E combi boiler. Each day, boiler fails to fire. Go to boiler - the pressure is right down to 0. Put pressure in to 1.3 - 1.4bar. Then the boiler will fire on both heating and hot water. However, when heating has been satisfied and boiler is not in demand...
  6. K

    Worcester leaking condensate

    I ve been looking at a Worcester 30cdi conventional which periodically leaks. Ive checked the trap and its clean, the trap has got the flexi drain and a 1/4 inch hose. Can anyone tell me what the two drain outlets are for? when I fill the trap under the sink the 1/4 hose spits out water, but the...
  7. Y

    Fitting / removing push-fit flexible tap connectors - any opinions or advice?

    Hi all, I've just bought two 22mm copper push-fit (type 2) flexible tap connectors with integral isolation valves, which I have fitted to a new bathtub that I've installed. Although I am capable of bending pipes and soldering joints, I chose to try something new, for three main reasons: firstly...
    • Yehia
    • Thread
    • advice connectors copper fitting fittings flexi flexible opinions removing tap which
    • Replies: 9
    • Forum: Plumbing Jobs | The Job-board
  8. K

    rusty monoblock tightening nut - help please

    Hello I'm recently qualified and to be honest haven't done much out ther yet so any advice welcome. Been to look at a simple kitchen tap replacement tonight. It's a pull out lever spray monoblock but the tightening nut on the rod seems very rusty and looks like it has no edges to get a grip...
  9. F

    Connecting flexi tap connectors

    I have a flexi tap connector with a rubber washer and nut on it. This nut will fit into the body of a mini ball valve if I remove the nut and olive. However that means the sharp edges of the valve pressing against the seat of washer - this does not seem a good idea. Is there a 'proper' way...
  10. M

    Connection for Duravit Starck 3 toilet cistern

    Hi, sorry for what will be a trivial question to a seasoned plumber, but I've just purchased a new Duravit Starck 3 toilet and cistern (close to wall version). I want to purchase a flexible hose to connect the cistern to the 15mm pipe providing the cold water supply, but there are lots of...
  11. AlexGas

    Quality!

    ....
  12. C

    Extractor fan for shower, how to vent

    Hi all, this thread is veering away from plumbing but I hope some of you will be able to help. We have an extractor fan in the bathroom of our bungalow. It is centered above the shower tray in the ceiling but if you go into the attic above it does not have any piping or flexi off it and just...
  13. A

    Hob + 1/2 " flexi

    Had to post this one. On a landlords gas certificate today i came across a hob connected by a 1/2 flexi tap connector. the compression connected onto a 15mm to 10mm reducer on the 10mm gas pipe!!
  14. S

    stainless steel flexi pipe instead of pex and copper

    Has anyone used the flexible stainless steel pipe ( similar to gas track pipe) for new heating systems or general plumbing. I had a look at it today in suppliers and it looks good. Slightly more expensive than pex but cheaper than copper. Has all the strength of copper but flexibility of pex...
  15. I

    Wirquin 40mm solvent weld flexi

    Hi, Does anyone know who stocks Wirquin 40mm magiflex solvent connectors? I'm up in Aberdeen and only know of B&Q locally who stock, but they're now becoming hit and miss. Cheers.
  16. G

    A flexi for boilers!

    Found this, it's expensive for what it is. it's a flexi and it's for boilers and central heating. The Polski plumbers and DIY'ers will be pricing for boiler installations now! LOL On another note, it's a reintroduction of stainless steel, which I hate it was terrible stuff when they brought it...
  17. R

    Flexi Tap connectors on central heating

    We are having wet system radiators moved and the plumber is suggesting to reconnect with flexi-tap connectors. I am not too happy about this as they look unsightly and I am not sure they are not fit for the job. Can any one comment on the suitablity of flexi tap connects on central heating...
  18. D

    flexi on towel rail.

    i came across this today, some class act had connected the 15mm flow, copper pipe using a flexible tap connector to the towel rail, i mentioned it to the punter, as i was only there to stop a toilet leak and he said i think he was a cowboy, i agreed !!!
  19. P

    bending 32mm plastic

    ive got a very awkward joint, trying to connect bottle trap to a 32mm plastic pipe coming in from outside soil pipe ive tried using flexi but to long and i dont want to buy the 32mm flexi pipe from bes £28.00 from B.E.S because it eats into profit and i doubt if ill use it often so can i bend...
  20. M

    glowworm flexi hx18 problem?

    hi, customer of mine has above boiler on an open vented system. installed 2009. first f1 & f5 flasing on boiler carried out checks and only thing i could find faulty was 3port valve in airing cupboard not switch over to heating. customer did say before fault appeaded on boiler that had no...

Newest Plumbing Threads

Back
Top