You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
flange
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term "flange" is also used for a kind of tool used to form flanges.
Hi,
Im installing a bathroom and the shower i have selected will need to have a pump installed to provide sufficient pressure. I have purchased a Stuart Turner 2.0 bar monsoon pump. I plan to cite this in the airing cupboard.
We have a traditional vented hot water system with cold water...
As above, reason im asking is because ive never had to drill a cylinder and dont really want to! Any1 had any experience with the salamander flange? If so will it be as good as using an essex?
cheers
Hi All,
just been asked by a customer who has a cottage round the corner from me if theres a pump on the market that will increase his hot and cold supply to the taps and showers ? the kitchen sink is on mains pressure which is all good the rest of the house is tank cold fed and the hot is on...
Hi all,
Sorry, this is a bit of a saga but I'm going to try and give all the details at the start.
How it was:
2 Storey house. Boiler on ground floor, indirect vented hot water cylinder on first floor, cold water tank sitting on the rafters in the loft.
One bathroom with just a bath (no...
JimHearne
Thread
after
airlocks
fitting
flange
hot
hot water
surrey
water
ive got to fit a salamander pump to a cylinder for a shower the outlet to dhw is 22mm ,but i want to put a separate connection for the pump/showers, i know i could cut into the tank but the immersion heat is not in use is there something i could use to if i take the heater out ie a reducer plate...
Hi,
I am trying to install a surrey flange in my hot water cylinder. After deconnecting existing pipework and male adaptor, I have discovered that my hot water cylinder has a rim protruding inside (at the bottom end of the thread) which effectively restricts the diameter of the hole to the...
Bubblesmad
Thread
colour
flange
installation
internal
problem
surrey
thread
hi
i'm fitting a surrey flange to my hot water cylinder and there's a really old endfeed 28mm or 1" bent tank connector screwed into the top of the tank. i'm hoping i will still be able to use it and scre that into my surrey flange, but if i have to change it to a different fitting can i reduce...
rolysatch
Thread
28mm
cylinder
fitting
flange
pipe
remove
vent
water
I currently have a hot water tank which is heated via my gas boiler which I think is called an indirect system. I have a shower water pump fitted to increase the pressure from my gravity fed shower. Things have worked fine for a long time but recently I've found that the water goes cold after...
I'm about to fit an Essex flange to a HWC for a 2 bar universal Monsoon pump in the attic. Does any one know how close to the inside of the top of the HWC the feeder pipe should go to maximize water temperature but minimize pulling in air. The flange will be sited 60mm below the joint between...
I am looking for a top entry cylinder flange. I am looking for the type that you can adjust the direction of the outlet rather than relying on the direction dictated when the flange is fully tightened.Where can I buy one? Thanks
customer wants a fridge freezer for ice and chilled water running from header tank on a gravity mains supply?.
can you do this?/?///:willy_nilly:
another request is to tap into the bath tap 22mm pipes and connect a 3bar pump for 2 showers instead of dedicated supply via essex flange
comments?:75:
REDSAW
Thread
american
bar
flange
freezer
fridge
potable
pumbing
pump
storage
temperature
water
I've just bought a shower pump and it states - Do not use jointing compound or tape. Not only that I can't use flux on solder joints! What's left? Anyone know?
I need to replace a waste disposal unit with a standard double bowl waste trap. The problem is the flange on the waste disposal unit is 115mm and the biggest sink waste that I can find is 86mm. Any ideas?
Hi all,
Doing a bit of restoration work. I am in the process of replacing the entire toilet unit.
The outlet pipe goes into the ground and is surrounded by this large hard ring (appears to be as hard as concrete) - see image.
Would really appreciate some advice on what to do with it. Do I...
I am fitting an shower pump (Salamander ESP 100, negative head) under the HWC in a gravity fed system.
I have run the pipework for the cold feed in, the cold out and the hot out, all in 22mm, as per spec.
But before i do the hot supply in from the cylinder, i wanted to check what's recommended...
realstokebloke
Thread
essex
flange
necessary
really
shower
tapatalk
using
Hi
Is there anyone who could tell me the exact size of nut holding in the essex flange. I have tried to measure and it's around 24mm or 1/34 inches. Just need the exact size so I can buy new.
Regards
Hi All,
I have just discovered that the flange (Essex?) that feeds my shower pump from the the hwc is leaking. It is positioned on the side about 8 inches from the top if that is any help. I have drained the cwt because as usual the gate valve doesn't work and also drained the hwt to below the...
Hi Folks
A friend of mine recently had new bathroom fitted. They have a gravity fed mixer shower but it keeps airlocking and losing all power. The guy that installed it couldn't work it out (not a plumber - general bodg..I mean builder!) so said shower must be faulty. They got MIRA guy in...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.