Hi,
Just after a little advise on this please, New heat only boiler being fitted to the existing system "straight swop". Zoned for heating but not for HW, Trying to run a cable could prove difficult as there solid floors! If fitting to existing do you have to add this zone? I have a feeling you...
I have been to fit a new dis-connector to a 30ci part number 2000802600. it doesn't look anything like the existing filling loop. The original dis-connector was 2000801908 but is now obsolete. Has anyone fitted the new loop to one of these boilers.
Thanks for any advice.
casaco
Install teams required, we have ongoing social housing install work, the work is a mixture of full hits ( boiler rads and pipework) conversions ( boiler keeping existing pipework and fitting new rads as required) and combi swaps. The work could also include vertical flues and condense pumps...
a few wks ago fitted 2 designer flat bar vert rads - I fitted to the 2 existing pipe drops the builder had let from ceiling . the radiators still now gurgle as if there is air in them - I have had just one on at a time and the noise stops put both on and it gurgles . all I can think of now is...
Seasons Greetings to all.......please can you give me you're expert opinion of brands and models etc for my following requirement (will be doing a complete replacement of my 20year existing boiler/CH system in Jan)
1) Which Vailant combi model would be suitable for a 2 bed medium sized...
Ziad
Thread
boiler
combi
existing
model
other
recommendation
vailant
water
Default Central Heating Pipework
Hi All
If you have the time could you have a think about the following for me please, any advice would be gratefully received.
I am doing some work for a customer early in the new year, Im replacing 3 x existing wall hung steel panel radiators with newer...
Leoki
Thread
central
central heating
existing
heating
pipework
question
radiators
system
I'm not sure if it is enough work for a plumber be interested, but we need to make some alterations to an existing soil stack on the outside wall of a house in Reading. The wc is moving, and I've made a new hole in the wall for the waste, but it needs hooking up to the existing branch in the...
So I have been working as a plumber for just under a year now and normally when I have to cut into existing pipe to add an addition to it, I find myself always using compression as the pipes still have a little bit of water in them. When I try to dry them off I begin to solder and I always...
bacon sarnie
Thread
compression
easier
existing
fitting
pipes
round
solder
soldering
water
Good evening all, I'm having a bit of trouble. I'm looking for a Chrome Towel Heater but it has to have 480mm between pipe centres. Really struggling. Can anyone help? Thanks.
I was told that if an engineer carries out a tightness test which passed and then connects gas cooker
Re-tests gas tightness and it passes then its correct procedure.
Is that true or do they still need to check any other gas appliances in the house ?
Or do they just carry on if it passes the...
Hi guys,
got a boiler to install on a really sludged up system, the customer has changed their minds about keeping existing rads and having new installed instead. now the existing pipework will still need to be flushed so was thinking of knocking up some hose pipe with some fittings attached so...
beesley121
Thread
about
cold radiator
connect
existing
hot rads
thinking
without
I intend to replace my combi boiler with a new one. The existing gas/central heating pipes run under the floor and then are enclosed in the wall until they emerge underneath the boiler. I am being given conflicting information relating to these pipes. One party says new pipes will have to be...
My Grundfoss UPS 15-50 pump has started to grumble on start up, so decided to replace with updated model prior to failure; on attempting to remove 12 yr old pump by isolating and unscrewing pump isolation valve with a large 12" flat face adjustable was a a complete no no [limited access]. Even...
Hi,
i have been to look at a job where the current combi boiler is to small for the system it is on, i have calculated it requires 5kw more and have suggested upgrading from the old worcester 32kw to a new vailliant 37kw.
the customer has asked can we just install a small boiler just to cope...
I'm thinking of increase the flowrate of my existing heating system but keeping it simple for an outsider like me. As a result I'm thinking of "lifting" the electrical and moving part of my existing Wilo Gold SR50 pump and replacing it with a Wilo Gold SR60 pump's part instead, while keeping the...
OCDRAGON
Thread
existing
mechanical
pump
replace
replacing
system
their
thinking
wilo
When you order a Pro or Platinum package from TradesmanWebDesign.com
and have an existing website we will discount the final cost by £99
Offer ends Friday 24th June
Hello
i have a system already installed, which I have been having problems with for a few years now - air in system - I have put a thread about it in the central heating forum - see trackback for info.
is anyone on here happy to come and set this up correctly for me and advise me if...
sapphire
Thread
check
existing
london
looking
plumber
setup
system
Need to install a shower pump on an existing gravity system that already has a power shower installed also with appropriate hot & cold feeds.
The shower pump will be for a shower in an en-suite on the other side of the house.
I can't get my head round if it's possible with the current setup &...
TomLane
Thread
existing
installing
pump
shower
shower pump
system
We had a new utility room built and planned to put a combi boiler on the wall. The existing 22mm central heating pipes from the existing WB floor standing boiler in another part of the house, were extended to suit the new position and 22mm capped tails were left sticking through the ceiling. We...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.