Search the forum,

angle

In Euclidean geometry, an angle is the figure formed by two rays, called the sides of the angle, sharing a common endpoint, called the vertex of the angle.
Angles formed by two rays lie in the plane that contains the rays. Angles are also formed by the intersection of two planes. These are called dihedral angles. Two intersecting curves may also define an angle, which is the angle of the rays lying tangent to the respective curves at their point of intersection.
Angle is also used to designate the measure of an angle or of a rotation. This measure is the ratio of the length of a circular arc to its radius. In the case of a geometric angle, the arc is centered at the vertex and delimited by the sides. In the case of a rotation, the arc is centered at the center of the rotation and delimited by any other point and its image by the rotation.

View More On Wikipedia.org
Recent contents Top users
  1. G

    Best angle drill/driver

    ....looking at the Bosch one with the multi angle moving head or the Dewalt 18v for tight corners under baths etc. Any one got any advice/recomendations on a decent one.
  2. C

    Getting a fall on a run of toilets

    Any advice appreciated got a job.with runs of 3 toilets connecting into vertical stack. When the 1st toilet is flushed a small amount of dirty water enters the last toilet, checked the falls and a bit of backfall and the cast bend to the cast stack is more like a tee. No blockages as all been...
  3. M

    solvent or push fit

    Under my shower can i use pushfit or do i need to use solvent ? Once the shower goes down access will be pretty poor
  4. D

    Soil Pipe Angle

    Hello, I am relocating a toilet in an upstairs bathroom and while I am at it I am replacing a cast iron soil pipe that runs the the height of the house venting just above roof height. The toilet waster outlet will be approximately 1.5-2 metres from the soil pipe. My question is in regards to...
  5. M

    Flue Dripping on Patio - Worcester Greenstar 28i Junior

    Hi folks, Hope somebody can help me with this query. We have a Worcester Greenstar 28i Junior combi boiler. Works well but I think the flue has not been installed correctly as it drips onto the patio, especially in this cold weather. From what I've read I think they should be installed at a...
  6. 3

    So you think you can just use an ANGLE GRINDER to cut holes in tiles! Sure?

    So you have some fancy porcelain tiles on the job and you think you can just angle grind your way through it to make holes. Right Idea? Well at ********* we would ask you to reconsider your approach. When you angle grind holes from the back of a tiles it is a crude approach, creates a lot...
    • 365drills
    • Thread
    • 40mm angle basin bathroom cores diamond drilling drills grinder holes hose installers pan pipe pipes plumbers porcelain power price shape tile drills tiles tools wall waste water work
    • Replies: 7
    • Forum: Plumbing Jobs | The Job-board
  7. I

    How to install a brass cold water tap in right angle same time is tight?

    Hi I tring to install a brass water tap on my garden sink, but there is a problem, I add 1-2 layer of seal tape (white color very thin) on screw part of brass tap, turning it into a brass tap connector, then tight it up. The problem is: when the tap and the connector are in tightest position...
    • iwico
    • Thread
    • angle brass cold cold water connector control fix gas install installation job pipe problem right screw seal sink tap taps tight time trade water water tap work yellow
    • Replies: 11
    • Forum: Plumbing Jobs | The Job-board
  8. H

    Right Angle Drills

    Has anyone got any views on the best right angle drill to get? I'm going to install my own pipes and radiators. It's a big old house with really thick joists. So I want to get the most rugged drill for the job. I've looked at a Bosch and a Dewalt. They seem ok. Also i'm unsure if I should get...
    • Hoof Hearted
    • Thread
    • adaptor angle bits bosch control copper dewalt drilling drills electronic hammer install job mains pipe pipes plumber power radiators right tools work
    • Replies: 16
    • Forum: Plumbing Jobs | The Job-board
  9. J

    Soil pipe angle??

    Hiya Guys, I am going to core drill through the wall behind a wc and join in to the soil stack outside. Do I need to angle the core drill to achieve a fall going outside or can I just drill through horizontally? Advise much appreciated.
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Tilers' Talk
Tiling Tools
Tile Advice
Electrical Forum
Tiling Standards BS5389
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock