You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
30he
The HeS 30 (HeS - Heinkel Strahltriebwerke) was an early jet engine, originally designed by Adolf Müller at Junkers, but eventually built and tested at Heinkel. It was possibly the best of the "Class I" engines, a class that included the more famous BMW 003 and Junkers Jumo 004. As it started somewhat later than these two designs, and was thus expected to enter service later, the Reichluftfahrtministerium (RLM) ordered Heinkel to stop work on the design and put their efforts into more advanced designs.
The HeS 30 was designed before the RLM introduced standardized naming for their engine projects. It was assigned the official name 109-006, and it was sometimes called the HeS 006 as a short form. Development ended just as these names were being introduced, so "HeS 30" naming is much more common.
Hi
I have a Potterton Performa 30HE in a one bedroom apartment. For a few months I have noticed that it takes several minutes before the taps to run hot. But last week they stopped running hot altogether. I have found that if I switch the electrical power to the boiler off and on again normal...
Hi
Please help I have a problem with the boiler main 30 he flashes low pressure or pump usually if it is switched to central heating I note that sometimes central heating and hot tap water go back to normal by themselves or after turning the prv.
I checked or fixed:
reconditioned diverter valve...
Hi guys went to the above breakdown this morning fan light flashing and flame failure no blockages in flue system ,
G.c 47 393 13
The condense runs to kitchen sink absolutely blocked solid , the trap in boiler was also blocked solid, all cleared out 2 leads of the trap 1 to earth one for...
Been called out to leaking Isar 30HE coming from the plastic body of the diverter assembly at the DHW outlet - from what I can see - not a lot of space in there! Boiler working fine, no pressure drop, leak stopped when isolating cold water inlet to boiler. Removed copper elbow and replaced 'o'...
any done much with these as got two in series in a pub
readings im having doubts about
propane (lpg)
o2: 11.3%
co2: 6.87
Co: 0ppm
Ratio: 0.0000
eff: 88.6%
Ex Air 117%
Draught: -0.260
manual doesnt list any spec regarding readings
ex air im sure is too high
am i missing something
Hi lads I got a call from a customer to say on Saturday that their boiler was making a funny noise vibrating slightly on start up and vibrating slightly running.
i told them to leave it off and I'd b out to them on Monday.
just wondering if anyone has had any similar probs with this boiler and...
Hi,
I attended a job with no heating but perfect hot water. When heating is selected status goes to 'c' and burner goes solid on for about 20 seconds then goes to flashing. No fault codes.
I initially suspected the diverter but oddly the flow pipe from the boiler is roasting and the return...
Went to one of these this week boiler locked out.
Reset, and fired then dropped out 5 times to lockout.
Checked ignition sensing probes and cleaned, then all 3 cables slid out of porcelain.
Combustion door seal was brittle on bottom right.
Ordered spares and fitted replaced seals, fired up...
Hi
Servicing this boiler and I have found the inlet working pressure is 12-13mbar when hot tap is running. At the meter is 24mbar working. 26mbar standing.
Would this be classed as At risk? Ideal has mentioned it would be as it would cause incomplete combustion. Anything below 14mbar...
Hi, I have a slow leak from the left side, pipe going out is warm, there is tap on it, and the leak is coming from the bolt cap facing me.......I want to take this off and refit, but how do I isolate the water coming through the boiler?
Regards
Hi Just a quick question as I am sure I will need Engineer ( I am a handyman but not touching that) to sort out but afraid of being ripped of.
My problem is that the Central Heating is working fine but when I turn on the Hot Water the boiler shuts down. I noticed that the pressure dial on the...
Had a problem with rads getting warm as the hot water was run for a period of time ( filling bath etc) replaced diaphragm with the kit and silicon greased everything all was right again.
two days later no hot water?? Diverter valve pins makes good contact with micro switch and the neon comes on...
Went a main combi 30he that was locked out on flame failure. When I reset it it lights but doesn't rectify so them drops the flame.
So I messed about with the leads etc and when I disconnected the the rectification lead from the top of the condense trap it then fired up and rectifies? Anyone...
Hi all,
Could someone help me out here please? I got 2 errors on Ariston clas 30HE.
Error 1
It shows 201 - manual says - DHW sensor short circuit / open line. Had a look where the sensor is supposed to be just to find a blanked off port and loose sensor wire. Boiler works fine though, just...
I have a Main 30HE with the problem that when you run the DHW, the CH flow pipe gets hot. Not all the heat is passing down there as the DHW does get hot, but this is going to cause some efficiency problems as radiators are getting hot if you run a tap for long enough, and it is probably going to...
MartyP
Thread
30he
being
cause
dhw
engineer
heat
leaking
main
probably
problem
running
Hi all
Please can someone help with my problem .
Basically my heating is fine but hot water will only work if the tap is on full blast , and then turning any other water supply on knocks it off .
I noticed the rod wasn't protruding fully out of the diverter valve body to activate the micro...
jayc
Thread
30he
hot
hot water
please
potterton
problem
water
water problem
Hi Folks,
Any of you had grief with replacing leaking 'o'rings on the Baxi Combi/105HE main heatexchanger and secondary heatexchanger's?
I've just replaced, for the second time, 'o'rings on the pipe between the main Hex and the Secondary Hex. No leaks when I left yet ovr a month down the line...
I had a leak on the secondary heat exchanger pipe and dropped the front electric box PCB holder to remove the panels. Because it was in the down position it filled with water and even though the electric was off I think its gone.
The leak was own to O ring failure on the bottom joint of the...
Hi folks,
First time playing with one of these beasts! It's been installed about 4yrs and never serviced until I took it to bits last week. Issue I faced was intermittent "flame lift" displayed.
I removed the burner to find this Ahaa! I thought, issue found so I cleaned this out and the...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.