Hello,
My first post and in need of help please so a big HELLO to all you lovely people :D
I have a Grant Combi MkII 70 with a Riello 50 70 RDB burner.
The boiler has been giving poor performance recently by delivering little hot water.
I have serviced the boiler to a point and it has...
Just been to do a load of gas safety checks on a block of flats, asides from having to I.D and disconnect a fire I came across another issue. I noticed that the pipe on the pressure relief valves, from the boilers I looked at were not quite right. Instead of exiting the property with two...
Foodface
Thread
different
discharge
pipe
piping
point
pressure
relief
right
soldered
hi,
I installed a Vaillant 831 ECO tech plus at my own house less than three weeks ago and this morning it started a humming noise on dhw mode, i lowered the temp which seemed to reduce the noise but id rather find the route of the problem. By afternoon it started doing so in heating mode.
il...
Hi guys!!
Just wanted to know if anyone can help me out, I am filling in my portfolio
and cannot get hold of my gas engineer for a week and a half (on holiday)
I am writing up 2 jobs we done last week and I am a little cconfused. We serviced a
vaillant ecotec pro24
standing pressure was...
Gav e
Thread
appliance
boiler
burner
point
pressure
pressures
working
Just got back from a breakdown on a Glowworm Fuelsaver MK2, fixed the fault and gave it a good service, as the customer commented it not been done for at least 5 years!! Stuck the analyser and I could not get a reading to stablelise.
I was getting readings of 0.0040, 0.0073, 0.0021, 0.0095 and...
got a call back to go to 1st thing
original job was landlord safety i did 4 weeks ago
since then tenant has been complaining of a smell of gas around the flue
landlord is trying to say its something i've done but i cant think what could be causing it
the gas valve wasnt letting by and passed...
Hi all, just wondering at what point do we start charging when we advertise no call out charge, say for boiler break down. Or it is down to our discretion and the nature of the problem? Slap me if this has been asked before. Thx in advance.
John_
Thread
boiler
charge
charging
hourly
point
price
problem
start
New for 2012 is the Plumbers Merchant
point of sale A5 leaflets for Porsadrill tile drills from 365.
Diamond core drilling of very hard porcelain tiles. We produce drills to bore holes into the very hardest porcelain tiles.
This point of sale box contains 50 leaflets and can be sent to...
I was wondering if any of you had this problem and could give me advice.
I had a call today from a costumer about POTTERTON Suprima 60-80. He has two boilers installed, one for DHW and one for CH.
The CH one has to be reset every 24h, otherwise it stops heating. Once it's reset, works fine for...
Syty
Thread
boilers
point
potterton
potterton suprima
problem
reset
suprima
Hi all,
Haven't posted many times but I need to check myself on this!
I'm studying towards my gas quals, so any pearls of wisdom greatly excepted!
my question is regarding gas fires,
I understand I can carry out my wp @ meter check for a gas fire, no probs there! then i should check the wp @ the...
I'm having a new range installed in a few weeks and aga say that the gas supply needs to terminate with a bayonet for them to perform the installation.
Should I get an RGI to visit first and sort out the pipe work, then the aga guy can install the range, connect the gas, electrics, test and...
PlumbGeoff
Thread
commission
connection
cooker
gas
point
range
should
wondering why i am an rgi when this info is given out ??
or am i just grumpy ??
http://www.ukplumbersforums.co.uk/central-heating-forum/34469-glow-worm-ultimate-40ff-not-sparking.html#post292054
Tested a full heating system to 10 bars last week. No leaks or pressure drops. The system has been runnning for around 3 weeks now in the customers home. Now, a call - great start to a quiet week. Apparently one of the rad valve nuts is now leaking slightly.
All nuts had jointing compound...
Hi does anyone have the manual for this gas fire or know where the spilage test point is. I tested it on the RH side but it was spilling loads do I've capped it off. Just wanted to make sure I tested it at the correct point.
Thanks in advance
I've got a 15mm drain off to install to my central heating and all I can find really is a compression tee to fit the drain off, which looks a little chunky.
Can I solder the brass drain off into a copper end feed tee, or will I have to settle with the compression tee?
Thanks.
Hi,
This is the first 30kw logic that I have fitted this one is giving me that is giving a low reading on gas rating. It is measuring 2.94m3/hr compared to 3.13m3/hr in the MI. - checked more than once.
Inlet OP pressure measured on the test point is 18.5mbar, meter OP is 21mbar. Ideal have...
cascas
Thread
advise
gas
gas rate
ideal
ideal logic
inlet
logic
point
pressure
Hi,
I have tested the Operating Pressure on ideal logic which is giving a reading of 18mbar on the test point on the isolation valve.
The manual states, that the external gas cock could further reduce the operating pressure when measured at its test point. The pressure drop is relative to...
cascas
Thread
color
drop
ideal
ideal logic
logic
point
pressure
test
valve
I have installed New Boiler Vaillant 837 today and on Comissioning it checking P1 Gas test point
found leaking..Has anyone experienced same with new boiler, I will be intouch with Vailllant Tech
as its Brand new
noticed B&Q trade point selling bacho 10" changeable wide jaw,,which they have never stocked before,, and already discontinued.. only £11 on offer, just my luck. ha
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.