Hi,
currently have a multi-fuel wood burner although pretty much condemned. Chimney got swept today and guy says perfect condition, concrete lined.
I'm looking to replace the stove only. The sweep said I should replace it with similar output (kw), although with the flue exiting the top...
Hi,
currently have a multi-fuel wood burner although pretty much condemned. Chimney got swept today and guy says perfect condition, concrete lined.
I'm looking to replace the stove only. The sweep said I should replace it with similar output (kw), although with the flue exiting the top...
Hi all,
I have a few newbie questions please about boilers.
1) Is there a method for me to see how much i'm likely to save to have a new boiler?
2) I have a "traditional" Ideal Classic, with a hot water tank, and run a power shower off it. If I have a new boiler, a combination, will the power...
hi guys new to this forum & i'm after a bit of help, ive installed bathroom suits before and i'm fine with installing and moving pipe work & sinks, baths & toilets around but ive been asked to install a shower unit which of course means a new waste aswell, my question is, if anything what do i...
Good Morning,
I have a Powermax 155 boiler which runs an open vented central heating system in a single floor flat. Yesterday I replaced the radiator in the main bathroom with a large towel rail. After reconnecting the plumbing to the towel rail and turning the central heating back on, none of...
nekekami
Thread
after
installing
radiator
radiators
rail
system
towel
towel rail
water
working
I'm considering relocating my washing machine out of the kitchen and into the cellar. There's both electric and water services down there but not sure what I could to remove the waste water. I'm guessing any drains are located higher than the discharge point on a washing machine - can the...
Sweeney125
Thread
installing
light
machine
washing
washing machine
water
Hey I have fitted many close coupled toilets and have no problem with these. Can any one offer any advice on installing low level toilets. Is there an easy way to no what height to put the L brackets that hold the cistern in place? Is the pan best fit first or the cistern. Any advice and tips...
hi all im looking for a L shaped bath left hand 1700. i have quoted from a claygate book which is 400 pound for standard acrylic one
without front panel or hinged shower screen.
i have noticed williams do one for £350 quid which includes front panel and screen. im worried about the quality...
Hello,
I had 2 belfast sinks to install - 1 in the kitchen and 1 in the utility. They came with fairly standard looking chrome wastes. I installed both in the same manner, and 1 seems to be doing just fine but the other has a very annoying leak! Can anyone help?
I put a good layer of...
Don't worry it's not what you think,
I am GSR but only through my employer, I think I know the awnser but thought I'd see what you guys think. Can I install a boiler in my own home? I don't think I'd be able to use my company's registration as we do work for a HA. I don't work privately so I...
Good morning
I was wondering if anyone has ever installed a bath by putting the bath feet up on bricks to accommodate the trap etc. I've seen people do this on a timber floor and solid floor but my question is how does the bath not skid or buckle off the bricks as the feet aren't...
Good evening all
Studying for my C&G 6129 and need some help to visualize my question below:
I wondered if someone could explain why you would use an auto-air vent (AAV) on a low pressure heating system and the advantages of doing so? i.e on a F&E fed fully pumped system?
Also, when I hear...
Hi guys, can anyone please clear this up for me?
I am looking to install a boiler in a cupboard but currently in the cupboard there is the electrical fuse board for the house.
Is there a certain distance that you have to be away from the board before you can fit a boiler?
Cheers
Danny Mair
Thread
boiler
cupboard
electric
fuse
gas
gas boiler
installing
oil
Hi, this image looks like the setup under my sink:
I have a cold and hot pipe where the cold is already attached to the washing machine.
Presumably I could just attach the dishwasher to the hot tap but that would just waste electricity heating and reheating water. Is there such a thing to...
Jake Cattrall
Thread
advice
could
cutting
dishwasher
installing
table
toolstation
water
Have you use tracpipe ,and how do you find the use of this material.
Im thing of the cost of copper and the cost of tracpipe/time for installing.
I suppose the a nail in copper is the same as in tracpipe.
Is it time to change like some of us have and now installing plastic pipe.
Also where is...
hi, my garden office is about 100ft from the mains soil pipe (which is unfortunately hidden under recently laid concrete:banghead:)
i want to build on a small extension to this room with a sink, toilet and shower.
i dont want one of those awful electric toilets that look like they belong in a...
ferrarimum
Thread
concrete
garden
installing
office
plumbing
shower
sorry
though
Hey All,
I'm currently doing a DIY bathroom refit. Can anyone help with this one.
Bought a shower tray from ebay. Its a brand new Wickes 27mm ultra low profile 900x900 quad (plastic type not stone), B&Q do an identical model described as Cascata 900x900 ultra low tray. Need a low tray due to...
lozoid
Thread
help
installing
profile
shower
shower tray
tray
wickes
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.