You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
inner
The Inner West of Sydney is an area directly west of the Sydney central business district, New South Wales, Australia. The suburbs that make up the Inner West are predominantly located along the southern shore of Port Jackson (Parramatta River), stretching south to the shores of the Cooks River. The western boundary of the Inner West is approximately the A3 arterial road (Homebush Bay Drive / Centenary Drive), which divides the Inner West from the Greater Western Sydney region. The Inner West is much larger than the Inner West Council local government area. The Inner West roughly corresponds with the Parish of Petersham and Parish of Concord, two cadastral divisions used for land titles.
Hi All,
This is a bit of a random one, but I'm a product designer working on a lighting project and I'm on the hunt for unused/waste/offcuts of the 60mm plastic flue inner that you get with some boilers.
If anyone in the Glasgow area has any of the white for translucent stuff, I would...
Hi, our Bunded 1000ltr plastic domestic oil tank leaking from inner to outer skin, was installed, as part of a new-build, in 2016, to supply a boiler.
When getting it refilled last week, the delivery driver pointed out that the outer skin was bowing out slightly and advised me to check it.
I...
Hi. Our builders hit a problem with extending the balanced flue through a new extension. Their solution was to have the outer, intake pipe terminate at an external wall, but add an extra section to the inner pipe to take the exhaust away from the next house. However, the gas boiler was...
Our house is fed by a spring. The water is soft and so on the acidic side. We had a new upstairs WC and sink fitted. However, over time the WC has gained some green stains down the inside back, where the water flushes down. I am guessing these are caused by the soft water and maybe some...
Hi, just wondered if anyone could help.
I have acquired a spare diverter and a inner diverter inner handle for a Bensham bath shower mixer tap, however this does not come with the cam cover, how do i remove this from the the old inner handle and refit.
Please see enclosed photo of the diverter...
Hi, have been out to look at this earlier today. Boiler won't even go through ignition sequence..... Have checked gas supply etc. Boiler is approx. 2 years old and has apparently played up from day 1 with this fault code. Tenant usually presses reset a few times and then fires up. They have a...
who's getting one
Ridgid Inner Tube Core Barrel Wrench, Size N | Save 14% | UKToolCentre.co.uk
The NEW RIDGID® Inner Tube Core Barrel Wrenches are used for Mineral Exploration, Geotechnical and Environmental Core Drilling and Soil Sampling. They are specifically designed for use with ISO 10097...
Hi
Would love some advice please.
I cannot for the life of me see how I can get the tap handle off in order to fit a new cartridge.
The handle is pulled down a 1/4 turn by pulling on a thin lever in order to get the water flowing. On this make the levers are embedded in the handle (its from...
been to this boiler to day and the last 3" of the inner flue have corroded. i have ordered the inner flue kit. potterton seem to think this will slide over the old inner flue . i noticed part way down the flue is a 4mm steel rod which goes through both inner and outer flue sections i am hoping...
This boiler is driving me nuts, I have spent hours trying to sort it, cost me a fortune on the phone to vokera tech who to be honest seem to be quite hostile at times, (anyone else feel that way?)
The problem is everything works fine, pump runs, fan runs, APS works but no spark, open the...
Elementary question I'm sure.. I've ended up with a huge bag of random bits and can't remember if they were sold and packaged as for some distinct purpose...
Shown here posing next to a spigotless trap.
Hi all,
Just wanted to send a short message to say thanks for everyones advice and knowledge I have fleeced on this forum. I passed my ccn1 and all elements this week and am chuffed to bits, now the real work begins I guess. On a seperate note, does anyone know who David Clayton is? I...
Just thought I would bring up the subject up for the newer gas registered plumbers about the need to double check the flue terminal construction and inner tube condition of flues on the Potterton profile,prima and profile Neta heats
They are coming to a age now were the terminals and inner...
Puddle
Thread
air
boiler
burner
eco
flue
gas
glowworm
high
inner
inside
installation
plumbers
potterton
pressure
problem
profile
remove
replacement
safe
switch
temperature
training
tubes
wall
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.