I am installing a three way shower (fixed head, bath and hand) and need to know what connectors to use to connect the five 22mm inlets and outlets to copper pipe. All pipework in the wall is 15mm copper pipes using york fittings. Is there and fitting out there that will connect direct to the...
Hi All.
Apologies if this has been asked previously. I have searched for days but cannot find the exact answer.
I am installing a new shower room downstairs and need to connect the water waste (40mm) from the shower and basin. There is a 90mm cast iron soil stack right outside so this seems the...
Leonruss
Thread
40mm
basin
boss
cast iron
connect
iron
mcalpine
waste
Had a job today, someone had been there before, woman had a leak on stack, half the kitchen had been demolished and new inspection point had been put in on stack as that was leaking. I arrived today and she was convinced that was still leaking. No it was coming from above, can see the water...
got a job commin up which im using pex. ive used sharkbite and john guest quick connects before with good success in australia but looking for a supplier for push fittings but cant seem to find a online supplier that ships to germany. i have found plenty that sell compression fittings but ive...
Hi,
I'm attempting to extend the plumbing under the sink a little, as the drainage pipe on the new washing machine doesn't reach the spigot.
I've bought a mcalpine flexcon 4 pipe thinking i could just connect that onto the tee and then attach the spigot to the end of that. The problem is...
Hi
I found this smart thermostat product on the web and am interested in it for a property that's not always in use. I can't find any user feedback anywhere else on the web and wondered if any of you professionals had any experiences you could pass on, positive or negative !
It's sold in...
Hi all. I have a tiny kitchen and want to fit a tabletop dishwasher to the existing washing machine plumbing. I think I have found the right thing to connect the cold water supply - it's called a compression alliance t bar from screwfix and I've attached a photo (hopefully).
However I am a loss...
Hi
Can anyone advise of what fitting is required to connect the pictured flexi pipe to a 15mm copper pipe? The diameter of the nut end is 28mm.
Thanks in Advance
Hi, I recently fitted bath and shower mixer taps to my bath but when swithcing to the shower function the water just dribbles out. Discovered the tap has a minimum pressure of 0.5 bar and I have a low pressure system which I assume is under 0.5 bar. So question is, if I buy a new mixer with a...
mattdailey
Thread
connect
mixer
pressure
pressure problem
problem
shower
water
water pressure
Went to a big country house today set in acres of ground with lakes, sheep, cows and horses all around but it`s now all offices, anyway the story ............
Entered the reception room which would swallow my 2 bed flat and have room left over to be shown a small toilet cloakroom hidden in the...
Hello,
I don't have enough space under my kitchen counter. Hence I need to place dishwasher near the sink and would like to know how can I connect the dishwasher inlet pipe to kitchen tap.
dishwasher inlet pipe will be standard dimension
I read somewhere that threaded 3/4 connector can be...
ankurgupta26
Thread
attach
connect
dishwasher
hose
inlet
inlet hose
kitchen
tap
valve
water
Got a cold main in this Uponor 16mm pipe that I need to connect onto.
Been told by someone you can get a compression adaptor to copper, but I thought every joint was crimped. Anyone know if that's the case or how the he'll I can connect onto it without having to buy the crimpers ect.
cheers
Hi guys. I'd really appreciate some advice on this one.
Basically I have installed a shower pump (all ok) and of course the recommendation is to fit an aeration Flange at the top of the hot water tank. Makes sense.
However - my water tank has a 22mm male input on the top and the couple of S...
Don't know too much about mechanics etc.
I need to get my timing belt done. Should I also get a new water pump? They're only £40 odd.
Mechanic said no but if it goes then does timing belt need removing? I thought it did.
Cheers
Hi
My boiler (vaillant ecotec pro 28) is giving f22 message. The manual (and this forum) tells me that it needs to be refilled but I'm struggling to see how to do it. The boiler is up in the loft and there is a flexible piece of tubing next to the boiler but it's not obvious to me how to...
robboplumber
Thread
black
connect
ecotec
filling
pro
pro 28
vaillant
valve
Hi guys,
Thought I'd ask the experts as I don't really have a clue about plumbing. I can follow instructions though...:blush5:
The problem is I have a basin with a hot and cold tap and I want to change it into a single mixer tap. Replacing the basin isn't really possible.
This guy...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.