You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
bubble
An economic bubble is a situation in which asset prices are much higher than the underlying fundamentals can reasonably justify. Bubbles are sometimes caused by unlikely and overly optimistic projections about the future. It could also be described as prices which strongly exceed the asset's intrinsic value.
Bubbles are sometimes referred to as a speculative bubble, a financial bubble, or a speculative mania.
In the early stages of a bubble, many investors do not notice the bubble for what it is. People notice the prices are going up and often think it is justified. Therefore bubbles are often conclusively identified only in retrospect, after the bubble has already popped and prices have crashed.
Has anyone worked to the txn150pterp kingspan unvented cylinders? They have an internal expansion bubble like the megaflows I believe. To repressurise the internal expansion bubble am I correct in saying turn the power off to the immersion/heating turn water off. Then open lowest tap to drain...
Hi guys was wondering if anyone can advise on the frequency of having to recharge a megaflo air bubble? I have had mine installed not for 6 months and noticed the turndish was dripping, so I shut the cold feed off, let the pressure off and regened the air bubble. This seems to have sorted the...
I noticed today that the pressure gauge on my incoming water supply was showing over 5 bar and creeping up fairly rapidly until it went past 6 (that's the max it goes to) and continued. The Megaflo pressure reducing valve should be 3 bar, and this is normally what the gauge shows. The only thing...
Hi guys,
I made a thread about this a few weeks ago. I have started a new one as the issue is slightly different and I'm not sure people would read it if I continued it on!
I have cold water dripping from the Tundish. I have a Fabdec Excelsior WDI unvented cylinder with an internal expansion...
Rystar00
Thread
about
bubble
cold
cold water
dripping
plumbers
tundish
water
Hi guys,
You were so incredibly helpful with a boiler issue I had last year that I thought I'd ask come back and see if I could benefit again from your kind and generous advice.
The issue I have at the moment is as follows:
I have a megaflo in my basement which is below ground level.
I...
Rystar00
Thread
about
bubble
engineer
expansion
flow
internal
times
I am trying to find out why my Megaflow CL210 loses its bubble regularly after three months and would appreciate any comments on why this might be. The current position is:
1. The unit was professionally installed in 1999 and seems in good condition.
2. There is secondary circulation system...
Mr_Duck
Thread
bubble
every
expansion
megaflow
might
months
pressure
three
water
Hi,
I have looked on this site for the answer to this question but couldn't find it.
My hot water pressure feels like its getting low.
System is 7 years old and has never been touched apart from the normal yearly gas cert.
All system is outside.
I wondered if it was to do with internal air...
nodyland
Thread
air
bubble
color
combination
megaflow
refill
tank
valve
water
Hello.
Just moved into a new house - water/heating was not working so I got it serviced and now is up and running.
Once the guy had gone, I see I get a (small) dripping discharge of cold water from the discharge pipe.
Water is always cold.
When hot water is not being heated, it stops...
Dreadnought
Thread
bubble
cold
cold water
cylinder
discharge
system
unvented
water
Have a problem in that the homeowner says it's discharging regularly (maybe after hot water use). Have changed TPRV and PRV. Also has new combi valve. System is fed via a break tank with a Grundfos booster pump. He says the tun dish is dry but a pint of water comes out of the discharge daily...
Mega flo 170l, leaking from t&prv, drained down and refilled to recreate air bubble, still leaking, all thermostats/ valves working.
grenade style valve, leaks when water reaches 50 degrees.
Books say that they can be adjusted but i cant see how!!
also how do you know that it isnt the baffle...
Hi a friend of mine has a designer radiator, like the old cast iron type, which has white coating. There is bubbling under the coating and some small cracks at the edges. Any ideas how I can repair this?
Cheers!
zhacwuyts
Thread
bubble
bubbling
cheap
find
job
leak
paint
pan
pipes
plastic
price
radiator
remove
system
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.