You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
micro
Micro Cars is an automobile company based in Peliyagoda, Sri Lanka, founded in 1995. It was established by automobile engineer, Dr. Lawrence Perera. Micro Cars is a fully owned subsidiary of Micro Holdings.
Hi there I'm GSR and still and have been to a couple of biasi no hot problems now. The pin on diverter valve never seems to come out enough to make the micro switch. Flow switch seems to work as red LED comes on. I tried replacing diaphragm without any luck. But the the bloody pin still stops...
Ginger plumbing
Thread
biasi
boiler
boilers
hot
hot water
micro
no hot water
oil
seems
still
switch
water
Any ideas lads it comes of with a fault code the to change flame sensing electrode done that no change I'm now thinking pcb or bad earth any help appreciated
I appear to have a blocked valve (entry and return in one unit). The pipe is warm so I'm assuming the blockage/failure is in the valve. Is it possible to get these valves? If so where from?
Good morning gentlemen.
I have a Saunier Duval boiler with lock out problems.
It has 3 micro-switches, two of which are operated by a spring loaded water operated diaphragm bellows which pushes a stainless pin out to impinge onto a clip on micro switch to actuate it.
1)Domestic hot water...
Does anyone use this rigid gas leak detector or can you recommend one for around £100. Cheers
micro CD-100 Combustible Gas Detector - RIDGID Professional Tools
Hi Guys,
Anybody any ideas to why a 6yr old boiler would go straight to reset when you call for heat or water, (from cold)
The boiler may take 8 or more pressing of the reset button before it works properly, and if programmer is switched off for approx 1 hr- then you call for heat. It works...
Got to go and look at one of these, Ive chatted to the guy on the phone. Not been to many of these, anyway ch works fine but goes to lock out in hw. It's about ten years old so not condensing. My thoughts are blocked hw h/x, would think lack of circulation causing over heat. Can any one tell me...
I fitted a vaillant 831 to a micro bore system , chemical flushed system with new rads added .
The boiler fires up , runs for a little while heats up rads ten shuts down , boiler only been fitted for 7 days ,
Vaillant engineer went out to check boiler and said it's to powerful for micro bore...
Have been asked to perform power flush on micro bore system and change all radiator valves !
Pipe work is in 10mm copper to the rads .
Any one ever done micro bore power flush ?
Just need any advice possible .
System is clean and all radiators work ok according to customer , i have not...
i have been fitting both types of cooker hoses for years but never realy wondered untill today if there is any difference in the gas flow etc throught them.
Hi, I have a prob with my boiler,,Everything starts up and seems to work but it won't lightup/ignite in ho****er or cenral heating mode.
any suggestions on where to look for the fault??? Bud
Hello all
I have a customer just called me emergency call.
They have drilled a small hole in their plastic 10mm heating pipe.
I have cut plasterboard back to expose
I have hardly any flexability in pipe at all.
Eassiest way i recon is to plug the hole, but can anyone suggest a way...
have micro bore job to price is for conversion to seal system with UHWC + system boiler !
will be power flushing system but have never had a micro bore to deal with .
pls advice if you have done power flush on micro bore what to watch out for + any suggestions are much appreciated .
cheers stan
my mate has the above boiler which is locking out when reaching temperature......i went and had a look yesterday but for the 30mins i was there it worked as it should....2 hours later he gave me a call to say it had locked out again!!
I'm thinking pcb has gone but don't want to get one until...
went to this boiler, it was showing low water level/no water circulation. Pressure was ok so i checked the Main Flow Switch...no continuity with the pump running. Changed it and.......still the same. The pressure gauge takes an age to show and changes when filling, so i am guessing it is full...
hi
any advice appreciated, heating switched off and now seems to be getting no power as no lightson at all. main fuse at breaker intact .any suggestions
tob.
Can anyone advise me.
I have a Halstead Ace High the CH works fine but the spindle that should come out of the Flow switch when taps turned on does not reach the micro switch. If i activate the micro switch manually it fires the boiler.I have ordered a new diaphram to fit but i am wondering what...
hi guys just after second opinion. not that familier with halstead ace. boiler fire o.k for heating but no hot water. visual noticed that d.h.w spindle moves but not far enough to make micro switch, same goes for primary flow switch, that spindle moves but not far enough to make primary flow...
dougal
Thread
ace
halstead
hot
hot water
micro
no hot water
spindle
switch
switches
water
hi guys just after second opinion. boiler works o.k for heating but no hot water. visual notices that pin on d.h.w isnt coming out far enough to touch micro switch and also pin for primary flow switch isnt coming out enough to touch primary flow switch. i removed both micro switches and manually...
dougal
Thread
ace
boiler
difficult
halstead
hot
hot water
micro
no hot water
switch
touch
water
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.